0
What else can I help you with?
An electric iron is plugged into a receptacle that has 110 V present. If the voltage loss from the panel to the receptacle is 6 V the line voltage at the panel is?
To find the line voltage at the panel, you need to add the voltage loss to the voltage at the receptacle. Since the receptacle has 110 V and there is a voltage loss of 6 V, the line voltage at the panel is 110 V + 6 V = 116 V.
If the temp is -140 Celsius what is the Fahrenheit temp?
Start by taking the number in Celsius and multiply it by 9. Then divide that number by 5, and then add 32. This is how you convert Celsius to Fahrenheit or use the equation F = (9/5)C + 32In this case, the answer is about -220 degrees Fahrenheit.
What is a method to improve the power factor?
Add capacitors from line to ground.
200 amp main and would like to add another 100 amp service in another room how can you do this?
If you are doing this you are effectively limiting your main panel to 100 A with normal duty cycles. This can get complicated and an electrician is advised. But basically you have a 100A breaker that would typically be for 220-240 volt service and you would connect to the main of the second panel. The size of the wire between the two panels would have to be sized correctly and you would only bond ground and neutral at the main panel and not the branch panel. You might want to move some of the loads from the main panel to the branch depending on load calculations. If you know what you are doing and have access to a clamp on amp meter you could measure how much of the 200 Amps you are using at the current panel. This can be dangerous, so get an electrician or be careful. <<>> In the trade this is called a sub panel. It is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.
How do you add more breakers to a main supply panel?
New breakers can be purchased separately, and simply snapped into place in the modern breaker panels. Turn power off to panel before removing breaker panel plate. If you do not know what you're doing, save your life and hire an electrician to do it.
What is 150 percent of 220?
To find 150 percent of a number, multiply the number by 1.5. In this instance, 1.5 x 220 = 330. Therefore, 150 percent of 220 is equal to 330. Or another way of solving these types of percentages, called whole plus percentages, is simple. 100% of any number is the number itself (100% of 220 is 220) and 50% of any number is exactly half of the said number (50% of 220 is 110) and then add the two together (220 + 110 is 330).
What four consecutive prime numbers add up to 220?
The four consecutive prime numbers that add up to 220 are: 47+53+59+61 = 220
An electric iron is plugged into a receptacle that has 110 V present. If the voltage loss from the panel to the receptacle is 6 V the line voltage at the panel is?
To find the line voltage at the panel, you need to add the voltage loss to the voltage at the receptacle. Since the receptacle has 110 V and there is a voltage loss of 6 V, the line voltage at the panel is 110 V + 6 V = 116 V.
What is 220 add 25?
245
How do you draw a hut in qbasic?
To draw a hut in QBasic, you can use the LINE statement to create the structure. Start by drawing a square for the base using four LINE commands, then add a triangle for the roof using three additional LINE statements to connect the peak of the roof to the corners of the square. For example: LINE (100, 200)-(200, 300) ' Draw the base LINE (100, 200)-(200, 200) ' Draw the bottom line of the base LINE (100, 200)-(150, 150) ' Left roof line LINE (150, 150)-(200, 200) ' Right roof line This creates a simple hut shape on the screen. Adjust the coordinates as needed for size and position.
How do you add?
This is how you add! 100 + 120 ___ 220 well you add the ones placed first, then you add the tens, then hundreds, then thousands, and etc.
How do you draw hut in Qbasic?
To draw a hut in QBasic, you can use simple graphical commands like LINE and CIRCLE. First, create the base of the hut by drawing a rectangle using the LINE command, and then add a triangular roof using additional LINE commands. For example: LINE (100, 200)-(200, 300), 15 ' Draw the base LINE (100, 200)-(150, 150), 15 ' Left roof LINE (200, 200)-(150, 150), 15 ' Right roof This code snippet outlines a basic hut structure. Adjust the coordinates as needed for your specific design.
What are the benefits of upgrading to a 150 amp electrical panel for a residential property?
Upgrading to a 150 amp electrical panel for a residential property allows for increased electrical capacity, reducing the risk of overloading circuits and potential electrical hazards. This upgrade also provides the ability to add more electrical devices and appliances, improving overall safety and convenience in the home.
How do you add 10 percent percent to 1500?
Multiply 1500 by .1 That equals 150 Add 1500 and 150
What method allows you to add components to a panel or frame?
add
What is the square root of 25 plus 220 plus 25 plus 200 plus 150?
The answer is 620. Simply add the numbers together like you would for two plus two. To check your work, a calculator is the best option.
What two numbers add to get 32 but when multiplied is -220?
-188
