0
for USA, Canada and countries running a 60 Hz supply service.
A purely resistive 240 volt heater [baseboard unit] with no fan will operate when connected to a 120 volt source.Either of the two "hots" in the heater can be connected to the 120 volt grounded circuit conductor [neutral].
The wattage output will be only one quarter of the rated watts, so it won't get mad hot, but it will work.
A 2000 watt 240 volt baseboard heater unit [typically 8 foot] will only allow enough current to generate 500 watts at 120 volts.
If the heater has a fan, then it won't work, because the fan motor won't operate correctly at the lower voltage.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
What efficiency difference 240v 120v baseboard heater?
240V baseboard heaters are usually more efficient than 120V baseboard heaters in terms of energy consumption because they require less current to produce the same amount of heat. This can result in lower heating costs. However, the actual efficiency also depends on the insulation of the room and the overall heating system.
Can you plug a 120v 20 amp wielder into a 240v 40 amp outlet?
No, it is not safe to plug a 120v 20 amp welder into a 240v 40 amp outlet. The voltage difference is too high and could damage the welder. It is important to match the voltage and amperage of the welder with the corresponding outlet.
How do you change a heater from 120 volts 3a to 240 volts 1.5 a?
the simplest solution is by connecting two 120v 3amps heater in series , the same can be used directly on 240v. However the current drawn will still be 3 amps & Not 1.5 amps. The heater output power will be double that of a single heater running on 120v. ( or equvalent to two heaters operating on 120v. supply ) A more expensive method is to use a stepdown transformer which can be powered on 240v & connect the heater on the transformer 120v side. this method will consume approx. 1.5 amps from the 240v supply.
If you have a 240V 22A welder which has a plug similar but smaller than a dryer plug can you use this in a 120V outlet?
No, a 240V 22A welder requires a 240V outlet for proper operation. Plugging it into a 120V outlet will not provide enough power and could damage the welder or create a safety hazard. It is important to always use the correct voltage and amperage for electrical appliances.
Can you run your neon sign of 120v 50hz 60hz 0.6a 7.5kv 30mA in an Australian 240v power outlet?
No. The neon sign is fed by a step-up transformer. Primary side 120V, secondary side 7500V. If you applied 240 to the primary side you would get 15000 volts on the neon tube. A flash over and then nothing. If you can find a transformer from 120V to 240V or 240V to 120V then you are good to go. Connect 240V to 240V side and you will get 120V out the other, connect the 120V side to the neon sign and you should have light. Transformer should be at least 100va. This will give you an output of .83 amps at 120V
What efficiency difference 240v 120v baseboard heater?
240V baseboard heaters are usually more efficient than 120V baseboard heaters in terms of energy consumption because they require less current to produce the same amount of heat. This can result in lower heating costs. However, the actual efficiency also depends on the insulation of the room and the overall heating system.
Can 240V washer run on 120V outlet?
No.
What happens if you plug a 120V appliance into a 240V outlet?
You will burn up your appliance!!!!!
If you put a 60W 120V bulb in a 120V lamp that has a transformer for 240V and plug it into a 240V outlet will it work or blow the circuitry?
Off hand no but your explanations are not clear as to who is doing what to whom,,
I have 240V 3 wire twistlock plug and want to wire it so I have 120V outlet?
Don't!
Can you plug a 120v 20 amp wielder into a 240v 40 amp outlet?
No, it is not safe to plug a 120v 20 amp welder into a 240v 40 amp outlet. The voltage difference is too high and could damage the welder. It is important to match the voltage and amperage of the welder with the corresponding outlet.
You are building a new house and trying to decide between 120v and 240v which is better More practical?
In the US, both 120v and 240v will be needed for your home, as different appliances need different voltages. Your TV needs 120V, while your electric dryer and stove will need a 120V/240V supply. If you have an electric water heater, or central AC unit, they will need a 240V supply.
How do you change a heater from 120 volts 3a to 240 volts 1.5 a?
the simplest solution is by connecting two 120v 3amps heater in series , the same can be used directly on 240v. However the current drawn will still be 3 amps & Not 1.5 amps. The heater output power will be double that of a single heater running on 120v. ( or equvalent to two heaters operating on 120v. supply ) A more expensive method is to use a stepdown transformer which can be powered on 240v & connect the heater on the transformer 120v side. this method will consume approx. 1.5 amps from the 240v supply.
If you have a 240V 22A welder which has a plug similar but smaller than a dryer plug can you use this in a 120V outlet?
No, a 240V 22A welder requires a 240V outlet for proper operation. Plugging it into a 120V outlet will not provide enough power and could damage the welder or create a safety hazard. It is important to always use the correct voltage and amperage for electrical appliances.
Can you take a 120V winecooler to Europe and use it with an 240V outlet and an adapter?
NO, unless you get a converter that converts 220 to 110.
How can you convert a 3 prong 240V appliance outlet to 120V without rewiring and replacing the outlet?
For USA, Canada and countries running a 60 Hz supply service.1) An outlet for 240V is totally different from a regular 120V outlet. 2) The wiring for 240V is also much heavier than for 120V.3) The double pole circuit breaker necessary for 240V is different to the single pole breaker used for 120V.4) Anyway it is not clear why you would want to try to change a 240V outlet to a 120V type?5) If you could log in and add some more details below here so we knew your reasoning for wanting this change to take place, someone may be able to assist you much further.The reason why I need to do this is because there is only one 3-prong 240V outlet in the water heater closet feeding an inline water heater and I want to install an instant hot water recycling system which runs on 120v I so need the extra power outlet.If you want to keep the existing 240V water heater then you cannot add another outlet to the circuit, not even a 240V one, let alone a 120V one!The wiring and its circuit breaker is only rated to carry the current for one water heater and nothing else. If you add another appliance to the circuit you risk causing a house fire: the breaker may buzz but not trip so that the wiring gets hotter and hotter until something catches on fire!So, if you are planning to buy a new hot water recycling system it surely deserves to be installed safely and correctly?So why not, for your instant hot water recycling system, have a licensed electrician install a separate 120V circuit with the correct breaker, the correct-sized cable and the correct outlet near to the existing 240V outlet?As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Can you run your neon sign of 120v 50hz 60hz 0.6a 7.5kv 30mA in an Australian 240v power outlet?
No. The neon sign is fed by a step-up transformer. Primary side 120V, secondary side 7500V. If you applied 240 to the primary side you would get 15000 volts on the neon tube. A flash over and then nothing. If you can find a transformer from 120V to 240V or 240V to 120V then you are good to go. Connect 240V to 240V side and you will get 120V out the other, connect the 120V side to the neon sign and you should have light. Transformer should be at least 100va. This will give you an output of .83 amps at 120V
