answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

Can 400volts heater element get supply from 230 volts?

No, a 400 volt heater element cannot be safely operated on a 230 volt supply. To avoid damaging the element and potential safety hazards, it is important to match the voltage rating of the heater element with the supply voltage.


Can you plug in a 12 volt pump into 400 watt inverter?

Yes, you can plug in a 12 volt pump to a 400 watt inverter as long as the pump's power requirements do not exceed 400 watts. Make sure the inverter is designed to convert 12 volts DC to 120 volts AC to power the pump effectively.


How do you obtain a 230 volts single phase supply from a 400 volts three phase four wire supply?

400 volt three phase on a grounded system is 230 volt single phase, with each phase 120 degrees apart. So, if you have a 400 volt, three phase four wire service (grounded service), you can pull one phase off and reference to the neutral for 230 volt service. Note this may not allow 115 volt service, unless there is also a center tap for each phase.


Can you use 12volts with .5A to power a 12 volts 400 mA device?

Yes, you can use a 12-volt power source with a 0.5A capacity to power a 12-volt device that requires 400 mA. The power source provides sufficient current since 0.5A (500 mA) is greater than the device's requirement of 400 mA. Just ensure that the voltage remains stable at 12 volts, as that matches the device's specifications.


What size wire do you use and do you need a 240 volt sub panel to send power to some lights and a 1500 watt 120 volt heater about 400 feet away?

For a 1500 watt 120 volt heater located 400 feet away, you would need to use at least 10-gauge wire to minimize voltage drop and ensure efficient power transmission. It is recommended to install a 240 volt sub panel near the heater location to account for the distance and potential power requirements for additional lights or equipment.

Related Questions

How much voltage require to run 400 volt actuator?

To run a 400-volt actuator, you typically need a power supply that provides 400 volts of alternating current (AC) or direct current (DC), depending on the actuator's specifications. It's important to ensure that the power supply can handle the required current and provide stable voltage. Always refer to the manufacturer's guidelines for specific voltage and current requirements to avoid damage to the actuator.


Can 400volts heater element get supply from 230 volts?

No, a 400 volt heater element cannot be safely operated on a 230 volt supply. To avoid damaging the element and potential safety hazards, it is important to match the voltage rating of the heater element with the supply voltage.


Why 400 Hz in Naval and Air applications?

At 400Hz all electrical equipment like alternators, transformers and electric motors become smaller to supply the same power than 50 or 60Hz equipment, they are using Bosh 90 amp auto alternators same size as BMW and Mercedes with some internal modifications that is capable of up to 8.4 Kw and 70 Volt 3 phase that is then inverted to 220 Volt with a transformer


What is the formula for calculating the full current load of a 400 watt light?

Assuming an incandescent bulb and a 120 volt supply the formula is Watts = Volts x Amps x Power Factor where PF = 1 for resistive load. Amps = 400 / 120.


What is the 3 phase power supply in sri lanka?

400


Can you plug in a 12 volt pump into 400 watt inverter?

Yes, you can plug in a 12 volt pump to a 400 watt inverter as long as the pump's power requirements do not exceed 400 watts. Make sure the inverter is designed to convert 12 volts DC to 120 volts AC to power the pump effectively.


Can a 400 Volt inverter be run on 460 volts?

The range of working voltages for a piece of equipment should be marked on the cover. If it says 400-460 v or a wider range, the answer is yes. Otherwise the answer is no.


What are the key features and benefits of a 400 amp automatic transfer switch?

A 400 amp automatic transfer switch is a device that automatically switches power sources during a power outage. Its key features include high power capacity, automatic operation, and reliability. The benefits of using a 400 amp automatic transfer switch include uninterrupted power supply, protection of electrical equipment, and convenience during emergencies.


How do you obtain a 230 volts single phase supply from a 400 volts three phase four wire supply?

400 volt three phase on a grounded system is 230 volt single phase, with each phase 120 degrees apart. So, if you have a 400 volt, three phase four wire service (grounded service), you can pull one phase off and reference to the neutral for 230 volt service. Note this may not allow 115 volt service, unless there is also a center tap for each phase.


Can you use 12volts with .5A to power a 12 volts 400 mA device?

Yes, you can use a 12-volt power source with a 0.5A capacity to power a 12-volt device that requires 400 mA. The power source provides sufficient current since 0.5A (500 mA) is greater than the device's requirement of 400 mA. Just ensure that the voltage remains stable at 12 volts, as that matches the device's specifications.


What size wire do you use and do you need a 240 volt sub panel to send power to some lights and a 1500 watt 120 volt heater about 400 feet away?

For a 1500 watt 120 volt heater located 400 feet away, you would need to use at least 10-gauge wire to minimize voltage drop and ensure efficient power transmission. It is recommended to install a 240 volt sub panel near the heater location to account for the distance and potential power requirements for additional lights or equipment.


Is a Packard 400 a 8 volt electrical system?

No. Is a 6 volt system.