0
More information about the make and model of the range, cooker, oven, etc. is needed to be able to answer this question, assuming it is asking about the fuses to go inside the frame of the appliance itself.
But if it is asking a general question about the size of circuit breaker that should be used to protect a range circuit, see the answer to the Related Question shown below.
What else can I help you with?
Which electrical unit is used to rate cartridge fuses?
Amperage is used to rate cartridge fuses.
Why are fuses provided for electric installations?
Fuses are used in circuits for one reason only. The fuses are there to protect the conductors from a higher than normal operating amperage.Each type of conductor has a current limit set out by the electrical code book. If the circuit amperage gets over that limit, the fuse will open the circuit and remove the voltage source from the circuit.
How much is a resistor for an electronic circuit?
Resistors are tiny devices on circuit boards. Prices should range but should not be expensive but dependent on the materials used and the nature of conductivity.
What does a 4a 250v slow blow fuse normally LOOK LIKE and Is it supposed to look like a fast blow with a bead of solder in the middle?
The information of, if the fuse is a slow blow or not, is printed on the fuse. In electrical terminology it is known as a time delay fuse. Smaller glass envelope time delay fuses will have a spring mechanism that can be seen through the glass envelope. Time delay fuses are used in circuit that have a high inrush current when the device is first switched on. A good example of this would be an electric motor. The bead of solder on the end of glass fuses is how the spring is supported to the end cap of the fuse.
What do you mean by Electric drives?
elecric drives are basically big electric motors which are used to drive generators
What size breaker should be used for an electric range?
A 40-50 amp breaker is typically used for an electric range.
What gauge wire should be used for an electric range?
For an electric range, it is recommended to use a 6-gauge wire to ensure safe and efficient operation.
What type of power cord should be used for an electric range?
An electric range should use a heavy-duty power cord that is rated for high voltage and amperage, typically a 4-prong cord with a 240-volt rating.
What wire gauge should be used for an electric range?
For an electric range, a wire gauge of 8 AWG (American Wire Gauge) is typically recommended to handle the high power requirements of the appliance.
Do you need two 30 amp fuses for a dryer?
Yes, typically electric dryers require two 30 amp fuses to operate properly. These fuses protect the dryer from electrical overload and should be installed in the dryer's electrical circuit. It's important to check the dryer's manual or consult with a professional to ensure the correct fuses are used.
What are fuses 75 and 76 used for on a 1998 BMW 528i e39?
fuse 75 should go to electric fan, and fuse 76 should go to ac blower final stage blower resistor
What electric element should be used so as to open the closed electric circuit?
which electric element should be used so as to open the closed electric circuit
What is a fair price for a used Kenmore electric range?
A fair price for a used Kenmore electric range would be between $150 to $500 depending on how old it is and the condition it is in. When selling any used appliance the best price should be 50 to 75 percent of what a new appliance cost's as long as the item is in good to excellent condition.
Is it cheaper to cook on a gas range or electric range?
I used to have propane service and it was very expensive. I currently use an electric stove and it's affordable to cook.
What are the main uses for electric range cookers?
The main use for an electric range cooker is primarily to cook products for consumption. These cookers can be used to fry, boil and poach as well as bake.
How can I find out what each of the fuses are used for 2000 Mazda Protege?
if you look on the back of the cover of the fuse box it should have a diagram with labels for all the fuses
What devices are used to protect people from an electric current?
Electrical devices such as circuit breakers, fuses, and ground fault circuit interrupters (GFCIs) are commonly used to protect people from electric currents. Additionally, electrical insulation, such as rubber gloves and mats, can prevent electric shocks in specific situations.
