0
No
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Is the striped or the solid wire hot?
White is typically neutral and black is hot. If you are talking about the bare wire, that is ground.
Solid wire vs stranded ground wire on a 200 amp service which one do you use on my home?
Stranded wire is the choice as you have tight bends and a short run, solid wire isn't very good in this format.
What do you need and how can you install a ground cable if your 240V outlet doesn't have a ground wire?
You need a 3 conductor wire with ground. For example if you had a 30 amp breaker for that outlet you would need 10awg 3w/ground. That's 10 gauge 3 conductor with ground and replace the old wire back to the panel.
Is a wire marked comm a ground wire?
Probably not. We'd need to know what the wire goes to in order to be certain about this.
How do you ground a plastic box ground wire attached to GCFI and ground at fuse panel. Do I need to ground at the box itself as well?
Grounding a plastic box is a little hard as plastic is a nonconductor.be satisfied with grounding to a ground wire.
Is the striped or the solid wire hot?
White is typically neutral and black is hot. If you are talking about the bare wire, that is ground.
Solid wire vs stranded ground wire on a 200 amp service which one do you use on my home?
Stranded wire is the choice as you have tight bends and a short run, solid wire isn't very good in this format.
What do you do with the ground wire when installing a new thermostat that doesn't have a connection for the ground wire It's a 4 wire Honeywell thermostat Is it ok to not connect the ground wire?
That Thermostat is LOW voltage. IT does not have a ground wire. There is no need for a ground. it only opperates on 24 volts. there may be a green wire but it does not mean it is a ground
Is 14 gauge wire always ground?
Not always. You could have a conduit with 10 pairs of 14 gauge wire - not every wire in that bundle are going to be ground. Ground is usually identified as having a green coating on the wire ... sometimes it is just bare copper strands or a solid copper wire.
What do you need and how can you install a ground cable if your 240V outlet doesn't have a ground wire?
You need a 3 conductor wire with ground. For example if you had a 30 amp breaker for that outlet you would need 10awg 3w/ground. That's 10 gauge 3 conductor with ground and replace the old wire back to the panel.
Does the ground wire on a 200 amp box need to be 3 ought also?
No, you can use #4 bare copper ground wire.
Is a wire marked comm a ground wire?
Probably not. We'd need to know what the wire goes to in order to be certain about this.
Why do your car speakers make a squeaking noise when driving faster it gets more high pitched and then when slowing down it goes to a lower pitch they are 6 x 9 which i put in myself?
you need to find a better ground . like a seat bolt . if that dosent work pull your CD player and hook to you ground wire (the black wire) to a good solid ground like the ant wire maybe even the cig lighters ground
How can you test a fuel pump out of the tank?
You can test the fuel pump by touching the positive wire on the positive post of the battery. You will need to ground the ground wire.
How do you install a sub woofer with an amp?
Its not as hard as people may think, but its only a few wires. u need a power wire from the battery to the amp. then a ground wire from the amp to a good solid spot on your chassi. then a remote wire from your radio to your amp....and thats it, just connect your speakers and enjoy.
How do you ground a plastic box ground wire attached to GCFI and ground at fuse panel. Do I need to ground at the box itself as well?
Grounding a plastic box is a little hard as plastic is a nonconductor.be satisfied with grounding to a ground wire.
Chrysler LHS disconnect alarm system so it will start?
You need to ground it out by opening the passenger door locate the green and red from the door to the car it should be the only one in front, take a strait pin and push it into the wire coating until it hits the wire inside next ground the pin to the car body with a solid conducting wire start the car and remove the wire ground and pin. this will disable the alarm but you need to make sure you do not lock the car until you get a remote working for the car or the alarm will go off again. Good Luck
