0
What else can I help you with?
Can you use a two wire horn to replace a three wire?
No, a two-wire horn cannot directly replace a three-wire horn. The extra wire in the three-wire system is usually used to trigger different sound patterns or tones, which a two-wire horn cannot replicate.
What would cause loss of power to the wires in the ceiling for a light fixture if the breaker is not tripped?
Bad ground connection. Corrosion on wire. Broken or cracked wire. Bad Switch. Mouse chewed through wire. just a guess but it may be faulty wiring in the fixture itself you can try to figure it out first try to problem solve it.did you replace an older one?is it a new fixture?did it work before or after you replaced it?andis it a fairly old one?you can replace it as a last resort.
What is the wire size for a 35 amp breaker to a ac unit?
You will need to use #8 wire.
Can a 40 amp breaker not a 4 amp breaker be used to replace a 35 amp breaker for ac unit?
No, it is not recommended to replace a 35 amp breaker with a 40 amp breaker for an AC unit. Breakers are designed to protect the circuit and the equipment, so using a higher rated breaker can lead to overheating and potential damage. It is best to use the correct amperage rated breaker for the equipment.
What wire goes to the rem on a amp?
The remote wire on an amp is usually connected to the remote turn-on lead from the head unit or a separate switched power source. This wire sends a signal to the amplifier to turn on or off based on when the head unit is powered on or off. It is typically colored blue on most wiring harnesses.
Why does an amplifier not working unless a battery wire is touching the remote wire on the amplifier?
Either your remote wire from you head unit to your amp is broken or not connected properly, you don't have a remote wire, or your head unit is faulty. Try another piece of cable as your remote wire from your head unit, and if it still does not work, your head unit is faulty. To save buying a new HU, you could wire the remote wire to your accessories, but be cautious as you could flatten your battery quickly if wiring incorrectly.
What would cause the fuel gauge to stop working?
There are a few possibilities: A bad sending unit (inside the tank), a broken wire or other faulty connection, a faulty gauge, a bad fuse...
Why does my 1964 falcon gas gauge not move all the way full?
Bad sending unit, corroded wire from the sending unit to the gauge, faulty fuel gauge are a few.
Engine idles rough and nothing happens when you remove no1 spug plug wire?
either your plug or plug lead is faulty replace both
Why might the fuel gauge not work on a 1994 Dodge Dakota?
Either the gauge is faulty, there is a broken or shorted wire between the gauge and the sending unit or the sending unit is faulty. Hopefully, it's not the sending unit; That's integrated with the fuel pump module inside the fuel tank and to replace it means replacing the entire fuel pump module. Not a fun chore, and requires the removal of either the fuel tank or the truck box (take your pick, one method is about as much work as the other).
Oil light STAYS on 2003 foreman 450 es ATV?
Your sending unit could be faulty or the wire is either grounded, open or you have big problems...
How do you replace the ignition coil on a 1990 Honda CRX?
The coil and distributor are one unit, there for, no coil wire. Yes it is a sealed unit and has to be replaced as one.
What would cause the outside temperature sensor and the air conditioner to not work on a 2003 Nissan Maxima and could the problems be linked to one another?
It could be a faulty wire or connection. It could also be a faulty sensor or display unit.
How do you replace horn switch on a 1997 ford F-350?
you have to buy the complete unit ,airbag and all, about 500.00 just wire up a separate horn wire
Where is the oil sending unit for a jeep wrangler?
right where the oil filter is, its that wire that gives you trouble when you try to replace the filter.
How do you replace oxygen sensor 1997 infinity q 45 t?
There are 4 of them on the car, so you need to know which one is faulty. To replace them is the same for all. Disconnect the connector to the faulty o2 sensor and using a o2 sensor socket or a wrench that will fit unscrew the sensor. Install the replacement sensor and reconnect the wire.
What wrong with your gas gauge on your 1941 Pontiac?
In most cases it is the sending unit in the fuel tank that is faulty. Disconnect the wire at the fuel tank and ground that wire, turn the key on and see if the fuel gauge goes to the full mark. If it does the sending unit has failed. The float is also known to fail and sink to the bottom.
