answersLogoWhite

0

To check a flame rod, disconnect it from the control circuit and use a multimeter set to read resistance in ohms. Insert one probe into the terminal of the flame rod and the other probe to the metal rod itself. A good flame rod will typically have a resistance reading between 3 to 30 ohms. If the flame rod shows no continuity or a significantly high resistance, it may need to be cleaned or replaced.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

Can a flame rod burn out?

A flame rod is a simple piece of heat-resistant metal (nichrome, inconel, etc) in contact with a flame. A flame consists of ionized particles undergoing chemical reactions and therefore is conductive. The flame rod takes advantage of that fact. The rod has a small potential on it and when the flame touches it, a small current flows from the rod through the flame to ground. This current is detected and uses to "prove" the flame. A flame acts as a diode but I don't recall the direction of electron flow and that effect isn't used in this application. The rod's response is instantaneous. That, and there being nothing to degrade, are the two main benefits. The major detraction is that active, powered electronics are needed to process the signal. All pilotless gas systems use flame rods. If the ignition system is by spark then the flame rod and the ignition rod may be the same. Other systems use separate spark and flame rods. Yet other ignition systems such as the hot body ignitor don't involve the use of sparks at all. A similar application is the pilot light sustainer. This little gadget detects when the pilot light goes out and sparks to relight it.


When you hold a metal rod over a flame the end of the rod away from the flame gets hot how does this happen?

Metals generally exhibit good thermal conductivity. When one end of the metal rod is held in the flame it absorbs thermal energy and becomes hot. Thermal energy is conducted quickly along the material (from hotter to cooler parts of the rod), and the other end eventually becomes hot. This principal is used in cooling systems for electronics (for example) with heat sinks drawing thermal energy away from hot components in order to radiate it elsewhere.


What color does the element Mg impart to the flame?

The flame test is not used to detect magnesium; a magnesium oxide rod is used as a support for the solutions of other elements in the flame test.


What is the black substance deposited on the glass rod?

The black substance deposited on the glass rod is likely soot, which is a carbon-based material that forms when organic matter is incompletely burned. This can occur when the glass rod is exposed to a flame or other heat source.


Why do you not check gas leaks with a naked flame?

Checking for gas leaks with a naked flame is dangerous because if there is a gas leak present, the flame can ignite the gas causing an explosion. It is safer to use a gas detector or soapy water to check for gas leaks.

Related Questions

How does a flame rod work?

The main circuit board in your furnace sends a small ac signal to the flame rod so now you have an ac potential from the body of the furnace to the flame rod, When the flame comes on between the body of the furnace and the rod it rectifies the ac in to dc, The flame actually acts like a diode. When this dc voltage is sensed by the control board it knows there is a flame present and thus keeps the gas valve on. Hope this helps


Why is a yellow flame observed when glass rod heated?

The yellow flame observed when heating a glass rod is due to the presence of impurities on the surface of the rod, such as residual organic materials or contaminants. When these impurities are heated, they undergo combustion and emit a yellow-colored flame. Heating the glass rod to a higher temperature can help burn off these impurities and restore a clear flame.


Can a flame rod burn out?

A flame rod is a simple piece of heat-resistant metal (nichrome, inconel, etc) in contact with a flame. A flame consists of ionized particles undergoing chemical reactions and therefore is conductive. The flame rod takes advantage of that fact. The rod has a small potential on it and when the flame touches it, a small current flows from the rod through the flame to ground. This current is detected and uses to "prove" the flame. A flame acts as a diode but I don't recall the direction of electron flow and that effect isn't used in this application. The rod's response is instantaneous. That, and there being nothing to degrade, are the two main benefits. The major detraction is that active, powered electronics are needed to process the signal. All pilotless gas systems use flame rods. If the ignition system is by spark then the flame rod and the ignition rod may be the same. Other systems use separate spark and flame rods. Yet other ignition systems such as the hot body ignitor don't involve the use of sparks at all. A similar application is the pilot light sustainer. This little gadget detects when the pilot light goes out and sparks to relight it.


When you hold a metal rod over a flame the end of the rod away from the flame gets hot how does this happen?

Metals generally exhibit good thermal conductivity. When one end of the metal rod is held in the flame it absorbs thermal energy and becomes hot. Thermal energy is conducted quickly along the material (from hotter to cooler parts of the rod), and the other end eventually becomes hot. This principal is used in cooling systems for electronics (for example) with heat sinks drawing thermal energy away from hot components in order to radiate it elsewhere.


Why is heat conduction through a metal rod faster if the rod is pointed DOWN into a flame than when it is pointed UP into a flame?

Because heat travels "up." I disagree. Heat travels "up" in a fluid, because the molecules expand and become lighter and "float" upwards. But in a solid? How can that be? If you notice, the question is asking about a rod being pointed down into a FLAME versus up. As we all know, flames "point" up, not down. Therefore it is hottest at the tip of the flame. This should answer the question. If not...feel free to message me.


Where is the flame sensor located on my furnace?

The flame sensor on your furnace is typically located near the burner assembly, close to where the flame ignites. It is a small metal rod that detects the presence of a flame and signals the furnace to continue operating.


What color does the element Mg impart to the flame?

The flame test is not used to detect magnesium; a magnesium oxide rod is used as a support for the solutions of other elements in the flame test.


What does Abbie drive?

Abby drives a flame red 1931 Ford Coupe hot rod.


What is a ceramic rod?

A ceramic rod is in some heaters that glow red in the flame. It uses coal so like a radiator! thanks for asking this question! I know everything! :)


What is the black substance deposited on the glass rod?

The black substance deposited on the glass rod is likely soot, which is a carbon-based material that forms when organic matter is incompletely burned. This can occur when the glass rod is exposed to a flame or other heat source.


If you want to melt a glass rod faster which of the region of the burner will you use?

You should use the inner blue cone region of the burner flame to melt the glass rod faster. This region of the flame is the hottest and most intense, providing the necessary heat to quickly melt the glass.


Furnace on and off few seconds after?

check your flame sensor