answersLogoWhite

0

Switch rating should match or be greater than the rating for the protecting breaker.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Natural Sciences

If your dimmer switch goes out will it make your lights not work?

If a dimmer switch goes out, it may cause the lights to not work at all or to stay at a single brightness level. This can be due to a faulty switch or wiring connection. It is important to check the switch and wiring to determine the cause of the issue and resolve it accordingly.


What is the current rating of the fused switch assimblies in the primary distribuiton center?

The fused switch assemblies in the primary distribution center have a current rating of [provide the specific rating found in the system or documentation]. It is important to refer to the equipment's specifications for accurate information.


How do you wire 3 way rotary changeover switch?

By changeover switch, if you mean forward reverse switch, the correct electrical terminology you should be searching is, wiring of an electrical drum switch.


Why is there continuity between ground and the hot wire on a light switch?

Continuity between the ground and hot wire on a light switch indicates a wiring fault or short circuit. This could be caused by incorrect wiring, a damaged switch, or faulty installation. It poses a safety risk and should be corrected immediately by a qualified electrician.


Should their be a spark inside a light switch when it's turned on?

If you are seeing a spark then the switch should be changed out right away. The spark is created by bad contacts within the switch its self. These bad contacts will create heat and eventually destroy the switch. Make sure that the rating of the switch is greater than the load that is connected to it. The only time a switch might draw an arc is when it is opened but it should never arc when closing. Yes there should be a spark when a switch is put on.

Related Questions

How do you switch from two wire alternator to a one wire alternator?

The switch will depend on the alternators and car wiring. The switch could require removing an external regulator as well. You will need a wiring diagram of the vehicle wiring to decide which wires to change.


How do you decide on the rating of a main switch?

The rating of the main switch is decided upon by the current incoming mains. The main switch can't be lower than the incoming. In order to upgrade the main switch, the breaker box will need a complete upgrade.


How can I find a 3-way switch wiring diagram with power at the switch?

You can find a 3-way switch wiring diagram with power at the switch by searching online for electrical wiring diagrams or consulting a home improvement book that covers electrical work. Look for diagrams that specifically show the wiring for a 3-way switch with power coming into the switch.


What is the maximum amperage rating for a 15 amp switch?

The maximum amperage rating for a 15 amp switch is 15 amps.


What is the maximum amperage rating of the 20 amp switch?

The maximum amperage rating of the 20 amp switch is 20 amps.


What if the wattage of the load is higher than the rating of the dimmer switch?

If the wattage load is higher that the rating of the dimmer switch then do not use the switch on that circuit. The manufacturer's components of the switch are only rated at a specific rating. Going higher than that rating will destroy the device and void any warranty that the switch might have. Always size the device to the load that you are wanting to control.


Maximum rating of a knife switch that can be opened under load?

Look on the inside cover of the switch for the specifications that are allowed by the manufacturer of the switch. A switch without arc chutes will have a very low rating.


How do you check double pole wiring?

Double pole wiring is checked the same way as single pole wiring. When you turn the switch on and the device works, in effect the switch is checked.


What is the recommended wiring diagram for a 60 amp disconnect switch?

The recommended wiring diagram for a 60 amp disconnect switch typically includes connecting the power source to the line side of the switch and the load to the load side of the switch. It is important to follow the manufacturer's instructions and local electrical codes when wiring the disconnect switch.


How do you change a brake light switch on a 83 Chevy pickup?

Under the dash, near the top of the brake pedal arm, you will see the switch. Unplug the wiring from the switch. Unscrew the switch from the arm. The body of the switch is threaded. Screw the new switch in to the arm. Unhook the wiring, and check to see if lights are working correctly. The switch can be adjusted by unplugging wiring, and turning the switch in, or out to adjust when the lights come on, as to pedal movement.


What are some common practices for light switch wiring?

Common practices for light switch wiring include connecting the hot wire to the switch terminal, connecting the neutral wire to the light fixture, and grounding the switch. It is important to follow local electrical codes and turn off the power before working on light switch wiring.


Wiring diagram for ignition switch for 1974 Chevy truck?

Ignition wiring diagram