answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

Is the strike plate part of a lock set?

Yes, the strike plate is a component of a lock set. It is installed on the door jamb and helps to secure the door when it is closed by engaging with the latch or bolt of the lock.


Use 2 wireless remote garage door openers for the same door?

Your wording is a little rough but I think you're asking if you can use 2 different openers on the same door, and the answer is yes. In most cases, there will be a way to program the openers, but sometimes you have to program the receiver on the door. There are a set of small switches inside the control that you can set to what ever code your door is set for. Your best bet is to check the website for the door you're working on. Tech support there will have all the answers you need.


Do you set the clock forward or back Nov 1 2009?

You'll set the clock back. Many people use the mnemonic "spring forward, fall back" to remember :)


Is setback or set back correct?

"Setback" is correct when referring to a reversal or delay in progress. "Set back" as two separate words is incorrect in this context.


Is temperature increase or decrease when the door open of a refrigerator?

When the door of a refrigerator is opened, the temperature inside the refrigerator typically increases. This is because warm air from the surrounding environment enters the refrigerator, causing the internal temperature to rise. The refrigerator's compressor then works to cool the air back down to the set temperature once the door is closed.

Related Questions

How do I remove the door of a Samsung refrigerator?

To remove the door of a Samsung refrigerator, first open the door and locate the hinge cover. Remove the hinge cover and then unscrew the hinge screws using a screwdriver. Lift the door off the hinge and set it aside.


What is the explanation for the term 'Throw of the hinge'?

The throw of the hinge determines how the hinge opens by where the hinge is set; it is the distance from the outside edge of the hinge to its placement point on the door and jamb. A widethrow hinge sets the pintel or pivot point away from the door to allow it to open up to 180°. Wide jambs usually require a wide throw hinge to allow the door to move unobstructed.


How do you adjust a door on a 2002 s10 pickup not the hinge?

Usually a new set of hinge pins and bushings bring the door back to alignment. If something got bent you basically have to re-bend it. I've seen it done with blocks of wood and a floor jack.


How can I fix door hinge holes effectively?

To fix door hinge holes effectively, you can use wooden dowels and wood glue. First, remove the hinge from the door and fill the holes with wood glue. Then, insert wooden dowels into the holes and let the glue dry. Once the glue is set, trim the dowels flush with the door surface and reattach the hinge. This method provides a strong and durable fix for door hinge holes.


How do you keep an interior door from closing by itself in a house?

The very easiest way is this: # Remove the middle hinge pin. (bottom hinge pin if you only have two hinges) # Set it on a concrete sidewalk, driveway etc. laying flat. # Hit it with a hammer in the middle. This will bend the pin slightly, causing friction in the hinge and, once put back in the hinge, it should hold the door in any position you open it to.


How can I safely and effectively remove a door from its hinges?

To safely and effectively remove a door from its hinges, follow these steps: 1. Close the door and locate the hinge pins. 2. Use a hammer and a screwdriver to tap out the hinge pins. 3. Have someone support the door as you remove the last hinge pin. 4. Carefully lift the door off the hinges and set it aside.


How do you Replace door threshold gasket?

To replace a door threshold gasket you have to place a pair of sawhorses outside and make sure they are set up so that the door can be laid flat on top of them. Take a screwdriver and insert it into the bottom of the pin on one of the hinges. Use your hammer to pound on the top of the screwdriver to force the hinge pin upwards and out of the hinge. Repeat this process for the rest of the hinges. It is important to keep the door closed while removing the hinge pins so that the door or floor is not damaged. Open the door slowly and pick and slide it over the side to remove it from the hinges. Set the door on the sawhorses. Inspect the threshold seal on the bottom of the door. Remove the strip by removing the screws on the bottom of the door and sliding the threshold seal out of the channel that holds it. Slide the new threshold seal into the channel and re-insert the screws to lock it into position. Remove the door from the sawhorses and take it back into the house. Set the door back onto the hinges, inserting it in the closed position. Re-insert the door hinge pins using a hammer to pound them all the way back into place. Open and close the door to see how the seal affects the operation of the door.


In Mad Gab what does the phrase Set Bacon Hinge Ahoy it mean?

Sit back and enjoy it.


How do you change the passenger side door on a 1996 ford explorer?

You first need to pull the electrical connections out from the door. You access them by taking off the interior panel from the door. Then undo the connectors. I would tag them some how just incase to ease in the installation. They need to come out back through the wire loom that goes in between the door and the body. The door will be heavy. Have a person on hand to help. To remove it all you do is remove the hinge bolts. There will be two for top hinge and two for the bottom hinge. Either remove the bolts from the door side or the body side. Whichever set is easier. It should be off. Then just change it out and re run the wire. Hope this helps. Good luck.


What is the best technique for using a door hinge router bit to create precise and clean cuts for installing door hinges?

The best technique for using a door hinge router bit to create precise and clean cuts for installing door hinges is to secure the door firmly in place, set the router bit to the correct depth, and move the router along the edge of the door slowly and steadily to create smooth and accurate cuts.


How do you find the factory code in the drivers door of a Lincoln Continental?

If its the code for the keyless remote entry, the buttons on the drivers door, The factory set code can usually be found on the right arm of the trunk hinge. Even it the code is changed, the code set at the factory (default) can still be used to unlock the door.


You installed 3 double action hinges on your new door Now your door wont close in the center of the Jam What did you do wrong?

Try removing the center hinge. See if the door closes. If so the hinges need to be set into the jam or the door deeper. Adjust and re-install them. Check to see if your door has a bevel, is the bevel backwards? GL.