0
How do you determine the correct replacement ballast for 120 volt T12 dual tube fixture?
There should be a label on the old ballast. If so take down all the information for amperage and voltage. You should then be albe to get a replacement at any Lowes, Menards, Home Depot, any other home improvent or electrical supply store.
What else can I help you with?
How can you attach a 120 v Light Fixture to a 277 v system do I need a ballast so what kinda of ballast?
To attach a 120V light fixture to a 277V system, you will need a step-down transformer with a 277V primary and 120V secondary. This will allow you to safely power the light fixture at the correct voltage. You do not need a ballast in this case, as ballasts are typically used with fluorescent lights and not for altering voltage levels.
Where is Fluorescent light wiring diagram?
Fluorescent light fixtures typically have a wiring diagram on the label or inside the fixture. The diagram will show how to connect the wires for the ballast and the tube sockets. It's important to follow the wiring diagram carefully to ensure the correct installation and function of the light fixture.
How many volts needed to run a fluorescent light?
The voltage of your area is what determines the operating voltage of all equipment. Equipment from other countries usually has to use a transformer to get the correct voltage. The voltage on a fluorescent fixture is printed on the ballast of the fixture. See if the voltage on the ballast matches the supply voltage of the system that you are going to use to operate the fixture.
How repair ballast?
Ballast meaning neon ballast You are dealing with lethal voltages and should never try to repair As ballast It is practically a non repairable item . Usually it is totally burn up and repairing if possible is not cost effectiveNext AnswerA ballast is not a repairable item. Taking one apart, unwinding the coil to find a break and repairing it is not practical. Especially if you had to clean out the tar like sunstance inside it to get at the parts. In a fluorescent tube fixture, the ballast is easily replaceable by a knowledgeable person. The replacement part is not expensive and an old wire coil ballast can be replaced with a more efficient electronic one.A small neon bulb ballast is just a small resister capable of handling the wattage going through it. It is easily replaceable but the bulb is so cheap the it isn't worth the labor. You can just get a replacement bulb.
How much power does a fluorescent fixture use with no tubes installed For example a switched on 8' fixture with a single tube with an old ballast.?
A fluorescent fixture with no tubes installed will still consume power, typically around 5-10 watts due to the ballast and other internal components. This power consumption is significantly lower compared to when the tubes are installed and the fixture is operating normally.
How do I perform a t8 ballast replacement in a fluorescent light fixture?
To perform a T8 ballast replacement in a fluorescent light fixture, follow these steps: Turn off the power to the fixture. Remove the cover of the fixture. Locate the ballast and disconnect the wires. Remove the old ballast and install the new one in its place. Connect the wires to the new ballast. Replace the cover and turn the power back on to test the fixture.
What is the process for t12 ballast replacement in a fluorescent light fixture?
To replace a t12 ballast in a fluorescent light fixture, first turn off the power to the fixture. Remove the cover and locate the ballast. Disconnect the wires and remove the old ballast. Install the new ballast, reconnect the wires, and replace the cover. Turn the power back on and test the light to ensure it is working properly.
Is it possible to use T8 bulbs in a T12 fixture?
Yes, it is possible to use T8 bulbs in a T12 fixture with the use of a retrofit kit or ballast replacement.
How to remove ballast for LED lights?
To remove ballast for LED lights, first turn off the power supply. Then, open the fixture and locate the ballast. Disconnect the wires connecting the ballast to the fixture. Remove the ballast and rewire the fixture to directly connect to the LED lights. Close the fixture and turn the power back on to test the lights.
Why Metal halide fixture with a 175 w bulb and correct ballast could overheat?
Make sure you are using a metal halide bulb and the ballast is matched to the wattage on the bulb. These both must be correct.
How can I bypass the ballast in a lighting fixture?
Bypassing the ballast in a lighting fixture involves removing the ballast and directly wiring the fixture to the power source. This can increase energy efficiency and extend the lifespan of the fixture. However, it is important to follow safety precautions and consult a professional if unsure.
How can you attach a 120 v Light Fixture to a 277 v system do I need a ballast so what kinda of ballast?
To attach a 120V light fixture to a 277V system, you will need a step-down transformer with a 277V primary and 120V secondary. This will allow you to safely power the light fixture at the correct voltage. You do not need a ballast in this case, as ballasts are typically used with fluorescent lights and not for altering voltage levels.
Where is Fluorescent light wiring diagram?
Fluorescent light fixtures typically have a wiring diagram on the label or inside the fixture. The diagram will show how to connect the wires for the ballast and the tube sockets. It's important to follow the wiring diagram carefully to ensure the correct installation and function of the light fixture.
How do you change the ballist in a light fixture?
Ballasts can be quite different even if you order a replacement part for a specific fixture. You need to follow the wiring diagram on the new ballast. If this is confusing or not easy to follow, you need a competent electrician to do this for you.
How many volts needed to run a fluorescent light?
The voltage of your area is what determines the operating voltage of all equipment. Equipment from other countries usually has to use a transformer to get the correct voltage. The voltage on a fluorescent fixture is printed on the ballast of the fixture. See if the voltage on the ballast matches the supply voltage of the system that you are going to use to operate the fixture.
How repair ballast?
Ballast meaning neon ballast You are dealing with lethal voltages and should never try to repair As ballast It is practically a non repairable item . Usually it is totally burn up and repairing if possible is not cost effectiveNext AnswerA ballast is not a repairable item. Taking one apart, unwinding the coil to find a break and repairing it is not practical. Especially if you had to clean out the tar like sunstance inside it to get at the parts. In a fluorescent tube fixture, the ballast is easily replaceable by a knowledgeable person. The replacement part is not expensive and an old wire coil ballast can be replaced with a more efficient electronic one.A small neon bulb ballast is just a small resister capable of handling the wattage going through it. It is easily replaceable but the bulb is so cheap the it isn't worth the labor. You can just get a replacement bulb.
How do you rewire a magnetic ballast F96T12 fixture to work with a new electronic ballast?
The end sockets have to be rewired. The schematic for the rewire is on the ballast label.
