by using a pressure regulator calibrated to 100mbar
Just doing some research on conversion myself and found the following resource which was helpfulhttp://www.ct.gov/drs/cwp/view.asp?A=1511&Q=267170basicallyCOMPRESSED PROPANE (GASEOUS FORM) EQUIVALENCY INFORMATION: At 14.73 lbs. of pressure per square inch (psi) and 60 degrees Fahrenheit: * 1 cubic foot propane = 0.0278 gallons propane * 100 cubic feet propane = 2.78 gallons propane * 1 gallon propane = 35.97 cubic feet propane * 100 gallons propane = 3597 cubic feet propane Hope this helps
Yes, hectopascal (hPa) and millibar (mbar) are equivalent units of pressure. Both are defined as 100 Pascals, making them interchangeable in meteorological contexts. Therefore, 1 hPa equals 1 mbar.
23.6 gallons. That's the volume of 100 lbs of propane, however, they only fill to about 80% (to allow room for expansion with temperature; otherwise you'd blow out liquid propane!).
A 100 pound propane tank has a capacity of 2,160,509 BTUs
20 percent of 100 pounds is 20 pounds. Therefore, if there is 20 percent left in a 100-pound propane tank, there are 20 pounds of propane remaining in the tank.
"A standard 100 lb propane bottle contains 90 litres of propane. " http://www.uniongas.com/business/otherci/techsol/heating/constructionheat/conHeatCostComp.asp
Propane is a gas a room temperature if it is not compressed. However, if it put in a canister under high enough pressure, it will be a liquid even at room temperature. Propane is a liquid below -44 degrees F or if its compressed. Grill bottles are only fillid 80% full with liquid. so you can use the propane gas on the top of the bottle.
1 millibar = 100 Pa(conversion website in link)
The pressure in the stratosphere ranges from about 100 to 1 millibar. This corresponds to an altitude range of approximately 10 to 50 kilometers above sea level.
The static pressure of propane at 70 degrees Fahrenheit will vary depending on the volume of propane and the specific conditions of the container it is in. To calculate the static pressure, you can refer to a propane pressure-temperature chart or use the ideal gas law equation (PV = nRT) with the known values of volume, temperature, and the number of moles of propane.
atmospheric pressure in measured in millibars
100 pound propane tank will hold 23.58 gallon. 100 pounds / 4.24 pounds per gallon = 23.58 gallons
.1333 kpa in 1 mmHg
80-90psi
You cannot use output pressure to tell how full a tank is. The pressure will remain constant until it's just about out of propane. You can use weight, if you know how much it weighs when empty, and when full - then it's just simple math.
That is the correct spelling of millibar (mb) and it means "1/1000th of a bar" which is a non-SI unit of pressure, chiefly atmospheric pressure. A bar is defined as 100,000 pascals (100 kilopascals) so that "standard pressure" on Earth is 1.01325 bars, equal to 101.325 millibars.
Just doing some research on conversion myself and found the following resource which was helpfulhttp://www.ct.gov/drs/cwp/view.asp?A=1511&Q=267170basicallyCOMPRESSED PROPANE (GASEOUS FORM) EQUIVALENCY INFORMATION: At 14.73 lbs. of pressure per square inch (psi) and 60 degrees Fahrenheit: * 1 cubic foot propane = 0.0278 gallons propane * 100 cubic feet propane = 2.78 gallons propane * 1 gallon propane = 35.97 cubic feet propane * 100 gallons propane = 3597 cubic feet propane Hope this helps