0
If you have corrosion problem then you also have a moisture problem. Clean up the corrosion problem first before the resistance of the connection causes heat and wire burn off. Once cleaned, there is a product on the market that can be sprayed on to the connection which will create a barrier to the moisture laden air. Once this barrier is in place the problem should be resolved. An effort should be made to remove the moisture from the air, maybe with a dehumidifier.
What else can I help you with?
What is the minnimum size equipment grounding conductor required by the NEC for a branch-circuit protected by a 50-ampere rated circuit breaker?
The minimum size equipment grounding conductor required by the NEC for a branch circuit protected by a 50-ampere rated circuit breaker is 10 AWG copper or 8 AWG aluminum.
Where on a motor vehicle would copper be used?
Copper can be used in motor vehicles for electrical wiring, connectors, and terminals. It is also commonly used in the production of radiators and brake lines due to its good thermal conductivity and corrosion resistance.
Can a double pole 20 amp breaker be used with 12-2 wire for a single 220 circuit?
The term "double pole" usually means a breaker with 2 handles that attaches in the space as a normal single pole breaker. If this is what you mean, no, you cannot. There is no potential, or voltage, between the wire terminals. If by "double pole" you mean what is usually called a 2-pole breaker, which is a breaker with 2 handles that attaches in the space of 2 single pole breakers, then yes, you can use this breaker and 12/2 wire to produce a 220v circuit.
Ground wire size for 200?
The size of the ground wire for a circuit is typically based on the size of the circuit breaker protecting that circuit. For a 200 amp circuit breaker, the recommended ground wire size is 4/0 AWG (American Wire Gauge) copper wire. This wire size helps ensure that the ground wire can safely carry any fault currents that may occur in the electrical system.
What size wire and circuit breaker is needed for an electric oven 4 wires with rated load of 34.9 amps 220v that is about 100 foot run from the electrical panel?
That would be a 40 amp 220v circuit. Circuit breaker is 40 amps and wire is 8 awg. Should use solid copper wire. Follow oven installation instructions.
What cleans corrosion off battery terminals?
Baking soda/water will neutralize. You can use a wire brush on terminals or one of those post cleaners with wire inside (if you have posts) Sandpaper works too. Also, if you put a copper penny between & can keep it there, the corrosion will attack it vs terminals.
What is the minnimum size equipment grounding conductor required by the NEC for a branch-circuit protected by a 50-ampere rated circuit breaker?
The minimum size equipment grounding conductor required by the NEC for a branch circuit protected by a 50-ampere rated circuit breaker is 10 AWG copper or 8 AWG aluminum.
What is the margin of safety with selecting circuit breakers?
The NEC requires that if the intended rating of a circuit corresponds to a standard size breaker then that size breaker must be used. In most instances, "rating of a circuit" means the intended connected load plus 25%. If the intended rating of a circuit does not correspond to a standard size breaker, you can go up to the next standard size without any other adjustments. In most circumstances, besides what I've already stated, a 14 gauge copper wire cannot be connected to a breaker larger than 15 amps, 12 gauge copper to a 20 amp breaker, and 10 gauge copper to a 30 amp breaker.
Is copper resistant to corrosion?
Yes, copper is resistant to corrosion.
What is the word equation for corrosion of copper?
The word equation for the corrosion of copper is: Copper + Oxygen + Water → Copper Oxide.
What size wire and breaker do you need for a 200 amp continuous duty circuit?
AWG 2/0 copper wire.
Where on a motor vehicle would copper be used?
Copper can be used in motor vehicles for electrical wiring, connectors, and terminals. It is also commonly used in the production of radiators and brake lines due to its good thermal conductivity and corrosion resistance.
Can a double pole 20 amp breaker be used with 12-2 wire for a single 220 circuit?
The term "double pole" usually means a breaker with 2 handles that attaches in the space as a normal single pole breaker. If this is what you mean, no, you cannot. There is no potential, or voltage, between the wire terminals. If by "double pole" you mean what is usually called a 2-pole breaker, which is a breaker with 2 handles that attaches in the space of 2 single pole breakers, then yes, you can use this breaker and 12/2 wire to produce a 220v circuit.
What size amp circuit breaker should be used for a gas dryer?
Typical residential electric dryers are on 30 amp circuits, which means 10 gage copper wire. The circuit breaker should match the dryer cord rating, generally 30 amps.
Can copper turning be used to test how pH affects copper corrosion?
Yes, copper turning can be used as a test specimen to observe the effects of pH on copper corrosion. By subjecting copper turnings to different pH solutions and monitoring the rate of corrosion, one can determine how pH influences the corrosion of copper. This experiment can help in understanding the behavior of copper in different environments.
Is copper corrosion resistant?
Yes, copper is corrosion resistant due to its ability to form a protective layer of oxide on its surface, which helps prevent further corrosion.
How do you wire a double pole breaker with 10 2 wire?
To wire a double pole breaker with 10 2 wire, first turn off the power to the circuit. Connect the black and red wires from the 10 2 wire to the two terminals on the breaker. Then connect the white wire to the neutral bus bar and the bare copper wire to the ground bus bar in the electrical panel. Make sure to follow all safety precautions and local electrical codes.
