0
To create a conical shape from a steel plate, you can use a template or layout tool to mark the specific dimensions and angle needed for the cone. Start by marking the center point of the plate and then create a circle with a radius equal to the desired base of the cone. From this circle, mark radial lines at the desired angle to form the cone's shape. Cut along the marked lines and then weld or fasten the edges together to form the cone.
What else can I help you with?
What is an element used to plate steel to make cars?
aluminum, maaaaaaaaaaaaaaaaaaattt what a fag
What words can you make with the word volcanoes?
love,can,no,nose,cone
How do you find the thickness of a plate if mass and radius are known?
There isn't enough information to make a calculation. If the mass is known and the radius is known, we can see that a steel plate with the given mass and radius will be thinner than a plastic plate with the same mass and radius. And a uranium plate will be thinner than the steel one if it has the same mass and radius. Without the density of the material or a knowledge of what it is (so we can look up its density), we're dead in the water. We can't solve it.
What minor plate is the largest?
The Pacific Plate is the largest minor plate. It covers a large area in the Pacific Ocean and is estimated to make up about 15% of the Earth's surface.
What plate boundaries make mountains?
convergent
How do you make a layout of a frustum of a hollow cone?
top & bottom diameters are given in a frstom & height is given.
Does Allegheny Ludlum make continuous mill plate steel?
Allegheny Ludlum makes continuous mill plate steel
Element that use to plate steel to make can?
tin
What element on the periodic table was used to plate steel to make cans?
tin
What element in the periodic table is used for plate steel and to make cans?
Tin is used for electroplating. it is also used to make cans.
Can having a steel plate in your head make you feel angry?
well, i'd be angry if I had a steel plate in my head......wouldn't you? Control your rage asker....there may be implants in the future of the future, patienceis a virtue; hoping is a healthy way to live.
To make a cone out of a piece of flat steel you have the arc laid out but you need some kind of tool to help roll the steel so you can weld the seem Does anyone know of a tool you can make or buy?
You can make a simple bending jig that will yield a cone, but it will not be perfectly smooth. The idea is a piece of flat or round steel stock that presses into the groove of another piece of angle iron. You can use threaded rod and a wrench or a floor jack to do the pressing. Email me at sbinternet at cox.net and I'll send you a picture with the basic idea.
How do you make cursor in Friendster layout?
hey!!! :) = How do you make cursor in friendster layout? =
Where in Maplestory can you get a steel plate?
Steel plates cannot be found in MapleStory. The only way is to: 1) Forge it using 10 steel ores and 450-500 mesos at either Vogen, Pi, Mr.Thunder, Muhamad, Chrishrama, or Chris. 2) Complete one of the following quests: Nella & Kerning City Citizen's Request, Keol's Order #2 Keol's Order #5 quest.
How do you make a MySpace layout code from scratch?
go to coolchaser.com and you can make your own layout
How do you find screwa on Maplestory?
You don't find them, you make them or do a quest. To make them you'll need: One Bronze plate (Made from 10 bronze ores) One Steel Plate (Made from 10 Steel ores) Then go to any item maker (There's one in Henesys, Ellinia, Perion and Kerning City) and they'll make 15 screws for you. Or do this quest, John and Pink Flower Basket, and you'll get screws from him at the end of the quest. You don't find them, you make them or do a quest. To make them you'll need: One Bronze plate (Made from 10 bronze ores) One Steel Plate (Made from 10 Steel ores) Then go to any item maker (There's one in Henesys, Ellinia, Perion and Kerning City) and they'll make 15 screws for you. Or do this quest, John and Pink Flower Basket, and you'll get screws from him at the end of the quest.
How can you make a cone out of paper?
To make a cone out of paper, start by cutting a sector from a circle. Then, overlap the cut edges to form a cone shape and secure them with glue or tape. Finally, trim the base of the cone to make it even.
