answersLogoWhite

0

Shut off the breaker that supplies the voltage to the fluorescent fixture. Wire the new pull chain switch in series with the black incoming wire and the black wire of the ballast. Turn the breaker back on and your switch will now control the off on operation of the light fixture.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

How does 4 tube fluorescent work?

A 4-tube fluorescent light contains four fluorescent tubes connected to a ballast that regulates the electrical current flowing through the tubes. When the light switch is turned on, the ballast sends high voltage to the tubes to ionize the gas inside. This ionization process produces ultraviolet light, which then interacts with the phosphor coating inside each tube to produce visible light.


How do you repair a dimmer and light switch in the same room?

For the most convenience, you should consider replacing two switches with just one switch that does both tasks. The first thing to do before repairing anything electrical is turn off the electricity to that room, then repair or replace the switch as you would any other light switch.


Which type of light bulb uses phosphors?

Fluorescent light bulbs use phosphors to convert ultraviolet light into visible light.


Is UV light the same as fluorescent light?

The UV light is different to that of fluorescent light. The UV originates from the sun. The latter one does not.No, it is not. UV is different.


How do you convert a standard light fixture into a pull-chain one?

Shut off the power to the light circuit. Remove the old light switch if there is one. Remove the old lamp holder base. Make a diagram and note how the wires were attached, what colour screws to what colour wire. At the light switch wire nut the two wires that came off of the switch together. The switch plate cover will have to be replaced with a blank cover plate to cover the old switch box. Install the new pull chain lamp holder using the notes and diagram that you made. Some of the lamp holders that have a switch in them will not have terminal screws. The wire to the switch will be the "hot" wire. The other wire from the old lamp holder will be the neutral which should be a white wire. Insert the bulb and turn the power back on. Now the pull chain will control the light rather that the wall switch.

Related Questions

How can I dim a fluorescent light?

You can dim a fluorescent light by using a dimmable ballast or a dimmer switch specifically designed for fluorescent lights. These devices control the amount of electricity flowing to the light, allowing you to adjust the brightness.


Is it cheaper to leave a fluorescent light on or switch it on and off?

Always cheaper to switch it off and on rather than leaving it on.


Which circuit can decrease the fluorescent brightness to the minimum amount?

You need to purchase a Fluorescent dimmer switch, no circuit can dim the brightness of the light safely.


How does a pull chain light work and what are its main features?

A pull chain light works by using a chain that is connected to a switch inside the light fixture. When you pull the chain, it activates the switch, turning the light on or off. The main features of a pull chain light are its convenience in easily turning the light on and off without the need for a separate wall switch, and its simple and traditional design that is commonly found in older homes or in areas where a wall switch is not practical.


Is the light switch loose in your room and in need of repair?

Is the light switch in your room loose and in need of fixing?


Why should the world switch to fluorescent light bulbs?

last longer and cost less on your bill


How can I adjust the brightness of a fluorescent light using a dimmer switch?

Fluorescent lights cannot be dimmed using a standard dimmer switch designed for incandescent bulbs. You would need a special dimmer switch compatible with fluorescent lights, such as a 0-10V dimmer or a dimmable ballast. These dimmers work by adjusting the voltage or current supplied to the fluorescent light, allowing you to control the brightness. It is important to consult a professional electrician to ensure proper installation and compatibility.


How do you operate a pull switch ceiling light?

To operate a pull switch ceiling light, simply pull the attached cord or chain downwards to turn the light on. Pull the cord or chain again to turn the light off.


Why does your light not turn off?

Pertaining to what? A light switch, an oven light, a pull chain type lampholder....???


Are my opportunities to buy fluorescent light bulbs soon going to be gone?

Fluorescent light bulbs are not going to be illegal to buy, but they make up a very low percentile of the light bulb market. It is highly recommend if you want save to money that you switch to energy efficient light bulbs.


How can I find a dimmable fluorescent light for my home?

To find a dimmable fluorescent light for your home, look for a dimmable fluorescent light fixture or bulb at a home improvement store or online retailer. Make sure the product is labeled as dimmable and compatible with your existing dimmer switch. You may also want to consult with a lighting specialist for further guidance.


How do you change a stuck fluorescent light?

Make sure the light switch is turned off before attempting to change the fluorescent light. Wear gloves to protect your hands while handling the light bulb. Twist the bulb counterclockwise to remove it, then insert the new bulb and twist it clockwise to secure it in place.