answersLogoWhite

0

If it is just under a 3 or 4 foot wide sidewalk, you dig down on either side and bore a hole under the sidewalk with a piece of pipe.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Natural Sciences

The primary purpose of an electrical service drip loop is to prevent water from?

The primary purpose of an electrical service drip loop is to prevent water from traveling along the service drop cables and entering the service entrance of a building. This helps to protect the electrical wiring and components from water damage, reducing the risk of electrical hazards and disruptions.


Why we should never handle electrical appliances with wet hands?

Because water is a conductor, and water dripping from your hands may drip down to an energized circuit, and effectively create a trail from that circuit to your hands, causing you to get electrocuted.


What is the metal piece under the window sill on the exterior of a house called?

That metal piece is typically called a "drip edge." It is installed under the window sill to help direct water away from the window and prevent it from seeping into the wall or foundation of the house.


What is a drip wire and could the lack of one cause water to get into the circuit breaker box?

This is an excellent question and yes it could.There is a "drip wire", there is a "drip loop".The drip wire is in the triplex that runs from the utility pole providing power to your house and the service mast on your house. The lineman will leave a sag in the wire so that water that accumulates on the wire will run along it to the lowest point and fall off harmlessly.The drip loop is the loop on the wire that runs into your house from your service mast. When these wires are connected to the triplex from the utility they should be tipped down so that no water will run down them. Now, this is the interesting part, at least to me...Even if you do all that, you can still get water in your breaker box. If those connections are tipped up, water can run down inside the insulation of service wire between the copper or aluminum and the inner jacket of the insulation. You wouldn't think it could, but it sure can. The only way I know to fix that is to have the utility company come out and if there isn't a loop, have them make one. They make think you're nuts, but that's ok, insist. So, what if you live in a cold climate or have an underground service. You can still get moisture in the panel. At the back of the metre base the electrician should have put in some "duct seal" . This prevents condensation from occurring from either the cold outside and the warmer inside, or warm outside and the airconditioned inside. Good luck, Andy


How do you make drip irrigation with a plastic bottle?

The easiest way to make a drip irrigation system from an old plastic bottle would be to punch a hole in the bottom of the bottle and connecting the bottle to a section of drip tape using a piece of spaghetti tube. Then elevate the bottle above ground level so that gravity will move the water to the drip tape and to your plants.

Related Questions

How can I install drip edge on an existing roof?

To install drip edge on an existing roof, you will need to first remove any existing shingles or roofing material along the edge of the roof. Next, measure and cut the drip edge to fit the length of the roof edge. Secure the drip edge in place using roofing nails or screws, making sure it overhangs the edge of the roof slightly. Finally, install new shingles over the drip edge to complete the installation.


How can I properly install drip edge on an existing roof?

To properly install drip edge on an existing roof, first remove any old drip edge. Then, measure and cut the new drip edge to fit the roof's edges. Secure the drip edge with roofing nails, making sure it overhangs the edge slightly. Finally, seal the edges with roofing cement for added protection.


How does a heparin drip prevent an existing blood clot from breaking off and traveling to lungs heart brain etc?

A heparin drip is used to prevent the blood from clotting. If there is an existing clot heparin will thin the blood, and prevent the clot from traveling to the lungs or brain.


What is purpose of electrical service drip loop?

To stop rain water from entering the service stack.


The primary purpose of an electrical service drip loop is to prevent water from?

The primary purpose of an electrical service drip loop is to prevent water from traveling along the service drop cables and entering the service entrance of a building. This helps to protect the electrical wiring and components from water damage, reducing the risk of electrical hazards and disruptions.


How do you install drip cap?

Roofing drip cap along the bottom edge of the roofed surface will go under the roof underlayment and shingles. Along the pitched edges of the roofed surface, the drip cap should be installed over the underlayment, but under the shingles.


Why does Water drip under 1993 Chevy Cavalier?

Because your fail


What percent of cultivated area is under drip irrigation in Maharashtra?

60%


What is the future tense of drip?

The future tense of "drip" is "will drip" or "is going to drip."


What is the purpose of drip edge nails in roofing installation?

Drip edge nails are used in roofing installation to secure the drip edge, which helps prevent water from seeping under the roofing materials and causing damage to the roof deck and structure.


What is the future tense of the verb drip?

The future tense of the verb 'drip' is will drip.


Is it normal to have puddle under car with climate control?

yes, condensation drip in normal