0
What else can I help you with?
With machine in neutral neutral light doesn't come on and electric start don't work?
Switch for neutral broken or not in correctly. It may operate a relay. Find it and see if it comes on and off with you switching the machine out of neutral and back. If it is fused check that. You can put your meter across the open fuse and watch the meter as you switch.
What color is common wire?
Normally the white wire is neutral, and the black is hot. But if the power comes into the ceiling box and the light is controlled by a switch leg the white my very well be hot. If there is only one wire in the switch box that is a switch leg.
Why does electric plugs in the wall not work when light switch is on?
Some custom homes were wired with with the receptacles that were switched. The receptacle was in a circuit with a switch controlling the the voltage to the receptacle. These circuits were mostly installed in living rooms. Table lamps were plugged into them so that when a person comes into the room, one switch would turn all of the table lamps. It could be that this switch has been replaced and installed up side down. So that when the switch was turned to the up position it was really turning the receptacle circuit off.
Does neutral wire carry voltage in a closed circuit?
The ground wire should carry no current at all, it is there in case of a short circuit to carry the (short circuit) current back to the breaker panel to trip the breaker. The neutral will carry the unbalanced load current between the 240 volt legs. e.g. L1 and N (neutral) 120 volts the load draws 8 amps. L2 and N (same neutral) 120 volts the load draws 12 amps. The difference between the two amperages is what the neutral will carry 12 - 8 = 4 amps.
Why is neutral line needed in home electricity?
The neutral line in home electricity completes the circuit by providing a return path for current to flow back to the electrical source. It helps balance the electrical load and provides a reference point for voltage measurements. Without a neutral line, the circuit would not function properly and could pose safety risks.
When the switch is closed it means that?
There is a complete path for the electricity to flow. The opposite of an open circuit. If a light switch is on and the light comes on, the circuit is closed. If the switch is turned off, the light goes off because the circuit is open.
With machine in neutral neutral light doesn't come on and electric start don't work?
Switch for neutral broken or not in correctly. It may operate a relay. Find it and see if it comes on and off with you switching the machine out of neutral and back. If it is fused check that. You can put your meter across the open fuse and watch the meter as you switch.
What color interior comes stock in a 2008 Chevy Cobalt?
The 2008 Chevy Cobalt comes stock with a neutral interior color. The neutral color is unique for the 2008 and it is not available also on the 2006, 2007 or 2009.
What color is common wire?
Normally the white wire is neutral, and the black is hot. But if the power comes into the ceiling box and the light is controlled by a switch leg the white my very well be hot. If there is only one wire in the switch box that is a switch leg.
Can you wire a standard on and off switch into an already existing circuit so that the off position completes the old circuit and the on position routes a new circuit?
A standard switch opens the circuit when in the off position, so the answer to your question is no. That said there is a way that it can be done by changing the switch to a single pole double throw switch. The "hot" will come into the switch on the common terminal. The old circuit connects to the top switch handle up terminal. The new circuit connects to the terminal in the handle down position. This setup will leave one of the circuits on all of the time. To over come this situation the switches can be installed in a double gang box. A standard on off switch will control the power to the "hot " that comes into the SPDT switch.
What are some examples of a closed circuit?
A connection from a power source, through a load and a return back to the power source. <><><> An example: electricity is supplied to the light switch on the wall through an insulated copper wire, even though the switch is in the off position electricity is present. There is another insulated copper wire going to the light bulb. When you flip the switch the circuit is completed and the light bulb comes on.
Where is the park-neutral switch in a 1998 Toyota Camry and where can you buy it besides at the dealer?
Park neutral switchLook down from the battery on the front of the transmission housing. Has lever and a linkage that comes from above, and big multiwire plug on top. can get at parts store, but really expensive. Junk yard? in Toyota manual (available at parts store) theres a scheme for testing switch before you install, and not all that hard.
How do you install a GFCI so it is always on to a two way light switch that controls a vent and a light in a bathroom?
Your question sounds simple but it isn't. There are two ways of wiring a light to a switch. One is to bring the hot and neutral wire to the switch box and from there run wires from the switch to the light. If this is the case you can install a GFCI on the circuit. The other way is to bring the hot and neutral wire to the light and from there run two wires to the switch and switch the light that way. In this case you cannot install a GFCI to in the switch box. <<>> The way you want the circuit to work has to be laid out as follows. Method one, the circuit that now controls the bathroom devices can be changed to a GFCI breaker. This is probably the quickest and cheapest, unless the job is new construction. Method two, if new construction use this method, as tearing walls open to get to the wiring will become costly. Where a supply circuit comes from the service distribution panel the first device on that circuit has to be a GFCI receptacle. This device has secondary terminals on it, that if connected every device downstream from it will also be protected. So if you supply the two way light switch that controls the vent fan and a bathroom light from the secondary terminals from the GFCI receptacle they will be protected.
What do I do when my 2000 Chevy Malibu is in park and I can't turn my key to the off position and the key still comes out of the ignition switch?
The neutral safety switch is bad, the ignition does not recognize it is in park. Your ignition switch may be bad.
What is a clap switch circuit?
A circuited switch, which operates with sound of clapping hands or something similar; ie. the switch comes to 'on' position when clapped once or twice, and to 'off' position when again clapped once or twice (depends on circuit design)
What is the purpose of a switch in a lighting circuit, specifically when it comes to controlling the flow of electricity, and how does it differ from a 3-way switch?
The purpose of a switch in a lighting circuit is to control the flow of electricity to turn the lights on or off. A regular switch has two positions - on and off. A 3-way switch, on the other hand, allows control of a light fixture from two different locations, such as at the top and bottom of a staircase.
Why does the circuit breaker keep tripping immediately?
The circuit breaker may keep tripping immediately due to a short circuit, which occurs when a hot wire comes into contact with a neutral wire or ground wire. This causes a sudden surge of electricity, triggering the circuit breaker to trip for safety reasons.
