answersLogoWhite

0

MAINS ELECTRICITY IS VERY DANGEROUSELECTRICITY CAN KILL YOU IF YOU DON'T REALLY KNOW WHAT YOU ARE DOING=IF YOU ARE NOT SURE YOU CAN DO THIS JOB SAFELY YOU MUST CALL IN A LICENSED ELECTRICIAN TO DO IT FOR YOU.=

User Avatar

Wiki User

17y ago

What else can I help you with?

Continue Learning about Natural Sciences

How many conductors in 220v 30amp circuit using?

A 220V 30A circuit typically requires three conductors: two hot wires and one ground wire. An additional neutral wire may be needed depending on the specific electrical configuration or equipment being used.


Do you need to use some type of mini breaker panel with a single 15A circuit breaker to connect a 15A receptacle into a 30A line?

Yes, you need to use a mini breaker panel with a 15A circuit breaker to safely connect a 15A receptacle to a 30A line. The breaker panel will protect the receptacle and wiring from the higher current capacity of the 30A line, preventing potential overheating or damage. It's important to match the amperage of the circuit breaker with the rating of the receptacle to ensure safe electrical operation.


Can 110V circuit with 2 wire size of 10 and a ground be converted to 220V after changing the outlet and breaker?

It depends on the amount of current (Amps) your breaker is rated for. If you boost your voltage the current will go down proportionally. 10 guage wire has an allowable ampacity of 30A. so if you are not drawing more than 27A you should be ok.


What size wire for a welding extension cord 220v 50 amps?

For a 220V 50A welder, you would need a minimum of 6-gauge wire for your extension cord to ensure it can handle the current safely. It's recommended to use a heavy-duty, outdoor-rated extension cord with appropriate wire gauge and length to avoid voltage drop and overheating.


In wiring for 220v can one use 2 15a breakers instead of a ganged 30a breaker?

No, when wiring for 220v, you should use a ganged 30A breaker to ensure safe and proper functioning of the circuit. Using two 15A breakers is not recommended as they may not trip simultaneously in an overload situation, potentially causing damage to the circuit or appliances.

Related Questions

How many conductors in 220v 30amp circuit using?

A 220V 30A circuit typically requires three conductors: two hot wires and one ground wire. An additional neutral wire may be needed depending on the specific electrical configuration or equipment being used.


What is the recommended wire size for a 30A circuit?

The recommended wire size for a 30A circuit is typically 10-gauge wire.


Can you make an extension cord that would have a NEMA l5-30p 30a 125v plug on one end and a NEMA l14-30r 30a 125v receptacle on the other end to connect a generator parallel kit to a transfer switch?

Yes. Use 10awg wire, mindfull of length voltage drop.


Do you need to use some type of mini breaker panel with a single 15A circuit breaker to connect a 15A receptacle into a 30A line?

Yes, you need to use a mini breaker panel with a 15A circuit breaker to safely connect a 15A receptacle to a 30A line. The breaker panel will protect the receptacle and wiring from the higher current capacity of the 30A line, preventing potential overheating or damage. It's important to match the amperage of the circuit breaker with the rating of the receptacle to ensure safe electrical operation.


Can 110V circuit with 2 wire size of 10 and a ground be converted to 220V after changing the outlet and breaker?

It depends on the amount of current (Amps) your breaker is rated for. If you boost your voltage the current will go down proportionally. 10 guage wire has an allowable ampacity of 30A. so if you are not drawing more than 27A you should be ok.


What size wire for a welding extension cord 220v 50 amps?

For a 220V 50A welder, you would need a minimum of 6-gauge wire for your extension cord to ensure it can handle the current safely. It's recommended to use a heavy-duty, outdoor-rated extension cord with appropriate wire gauge and length to avoid voltage drop and overheating.


What happens when a 20amp device connects to a 30amp receptacle and the power supply fails - will it trip the breaker?

Assuming you are referring to the power supply failing in your 20A device, it could cause the 30A breaker protecting the receptacle to trip. It depends on the mode of failure. It is easy to imagine a condition where a short in the power supply could cause a current in excess of 30A to flow to the device and trip the breaker.


In wiring for 220v can one use 2 15a breakers instead of a ganged 30a breaker?

No, when wiring for 220v, you should use a ganged 30A breaker to ensure safe and proper functioning of the circuit. Using two 15A breakers is not recommended as they may not trip simultaneously in an overload situation, potentially causing damage to the circuit or appliances.


Can you run a 30A dryer on a 50A receptacle?

You can always run under a receptacles rating. This just means how much current can be drawn thru the breaker before it will trip.


Can you safely change a 30 amp breaker to 20 amps?

No, this is not a recommended procedure. The breakers main job is to protect the wire that is connected to it. A 20A breaker will have a #12 wire (rated 20A) connected to it. A 30A breaker will have a #10 wire (rated 30A) connected to it. As you can see if you use a 30A breaker on a #12 wire you could overload the wire by 10 amps. I have seen an incident where the insulation has melted off of an overloaded wire, the wire short out and a fire start before the bigger size breaker tripped. DON'T DO IT.


What breaker do you use for 10-2 wire?

For 10-2 wire, you would typically use a 30-amp breaker. This size breaker is commonly used for 10-gauge wire in residential electrical installations. Make sure to check your local electrical codes and the manufacturer's recommendations for the specific application.


If you have a 240V dryer and installed 30A breakers on both sides of the line reads 120 and 120 how do you get 240 and you have a receptacle that reads 30A 125250 and still does not work?

you do NOT put two 110v breakers in. you put 1 two pole breaker in. the panel is designed to give you 220v off one side OR the other side if you use a 2 pole breaker on one side or the other side. If you look at both 120V lines on an oscilloscope you will notice that they are both 120V to the neutral, but they are 180 degrees out of phase. This means that when one hot is at +120V the other is at -120V. So between the two you have 240V. If you put your meter across both hots you should see 240V. If you do not see 240V across both hots you (or an unlicenced electrician) has wired the outlet without using a proper 220V breaker. You do not see 240V because the hots are in phase, to the voltage differential is 0V, not 240V. 220V breakers cannot do this, unless forcebly installed in the wrong type panel. More than likely someone tried to wire it with 110V breakers.