answersLogoWhite

0

This type of question usually means you aren't ready to do this yourself. Study some electrical material and the National Electrical Code and work this answer out for yourself. If I were to give you an answer, you might attempt to do something you shouldn't be doing, and that may cost someone a shock, a home fire, or their life.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

Is a cu wire a ground wire?

The type of wire does not generally determine whether something is a ground wire or not. A wire is a ground wire if it is connected to the ground of a circuit, or the common ground (the reference point of a circuit that is at 0 volts). However, in relation to the grounding rod used to connect the main circuit panel for a house, the rods are almost always made of steel that are copper plated.


Does the ground wire from a 240 volt tankless water heater connect to the common wire?

Any ground wire has to be connected to an independent ground wire that returns directly to the distribution panel and not to the neutral of the circuit.


Ground wire size for 200?

The size of the ground wire for a circuit is typically based on the size of the circuit breaker protecting that circuit. For a 200 amp circuit breaker, the recommended ground wire size is 4/0 AWG (American Wire Gauge) copper wire. This wire size helps ensure that the ground wire can safely carry any fault currents that may occur in the electrical system.


What is the white wire for in an electrical circuit?

Answers for USA, Canada and countries using similar 60Hz mains suppliesThe white wire is the "Neutral" wire. The Black wire is the "Hot" wire.The Green wire is the local "Ground "wire.If you do any such work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.IF YOU NOT ALREADY SURE YOU CAN DO SOME ELECTRICAL WORKSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


What size wire and circuit breaker is needed for an electric oven 4 wires with rated load of 34.9 amps 220v that is about 100 foot run from the electrical panel?

That would be a 40 amp 220v circuit. Circuit breaker is 40 amps and wire is 8 awg. Should use solid copper wire. Follow oven installation instructions.

Related Questions

How to install a 50 amp breaker in a circuit panel?

To install a 50 amp breaker in a circuit panel, first turn off the power to the panel. Remove the panel cover and locate an open slot for the breaker. Connect the hot wire to the breaker, the neutral wire to the neutral bar, and the ground wire to the ground bar. Secure the breaker in place and replace the panel cover. Turn the power back on and test the circuit to ensure it is working properly.


What is a branching circuit?

Each of the circuit breakers in the service panel controls electricity on a branch circuit. A branch circuit is typically a loop of wire that runs from the service panel, out to receptacles, light fixtures, appliances, etc. and back again.


What is the purpose of the white wire in an electrical circuit and how does it function as the neutral wire?

The purpose of the white wire in an electrical circuit is to serve as the neutral wire. The neutral wire completes the circuit by providing a return path for the current to flow back to the power source. It is connected to the ground at the electrical panel to ensure safety and proper functioning of the circuit.


What is the earth wire inside a plug for?

This wire provides a low impedance return path to the distribution panel in case of a circuit fault. This direct fault current path will trip the circuit's breaker and open the circuit.


How to install a 30 amp breaker in a circuit panel?

To install a 30 amp breaker in a circuit panel, first turn off the power to the panel. Remove the panel cover and locate an open slot for the new breaker. Connect the hot wire to the breaker, the neutral wire to the neutral bus bar, and the ground wire to the ground bus bar. Insert the breaker into the slot and secure it in place. Turn the power back on and test the circuit to ensure it is working properly.


How could you get more than one electrical circuit in the garage?

Run another wire from the electrical panel.


Is a cu wire a ground wire?

The type of wire does not generally determine whether something is a ground wire or not. A wire is a ground wire if it is connected to the ground of a circuit, or the common ground (the reference point of a circuit that is at 0 volts). However, in relation to the grounding rod used to connect the main circuit panel for a house, the rods are almost always made of steel that are copper plated.


How do you wire an electrical panel?

To wire an electrical panel, you need to first turn off the power supply. Then, connect the incoming power wires to the main breaker. Next, connect the branch circuit wires to the individual circuit breakers. Finally, label each circuit breaker for easy identification. It is important to follow all safety guidelines and local electrical codes when wiring an electrical panel.


Does the ground wire from a 240 volt tankless water heater connect to the common wire?

Any ground wire has to be connected to an independent ground wire that returns directly to the distribution panel and not to the neutral of the circuit.


How do you wire a GFI breaker?

To wire a GFI (Ground Fault Circuit Interrupter) breaker, first turn off the power to the circuit. Then, connect the hot wire to the breaker's terminal, the neutral wire to the neutral bar, and the ground wire to the ground bar. Finally, attach the breaker to the panel and turn the power back on.


How to wire a circuit breaker properly?

To wire a circuit breaker properly, first turn off the power to the circuit. Then, connect the hot wire to the breaker terminal and the neutral wire to the neutral bus bar. Finally, connect the ground wire to the ground bus bar. Make sure all connections are secure and the breaker is properly seated in the panel before turning the power back on.


Ground wire size for 200?

The size of the ground wire for a circuit is typically based on the size of the circuit breaker protecting that circuit. For a 200 amp circuit breaker, the recommended ground wire size is 4/0 AWG (American Wire Gauge) copper wire. This wire size helps ensure that the ground wire can safely carry any fault currents that may occur in the electrical system.