answersLogoWhite

0

These types of lamp sockets are known as pigtail sockets. Used in lighting fixtures they can not be repaired unless you have the means to re tighten the rivet that is used in the bottom of the lamp base. Any lighting store will have replacement parts for these types of fixtures. Molded pigtail lamp holders are used for temporary lighting in the construction trade. These lamp holders are positioned on brewery cord and can be placed at any needed position on the cord.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Natural Sciences

Why does a non grounded plug have four screws for two wires?

Typically the silver screws are neutral, the brass screws are for "hot" (if there are silver screws) There are two on each side because that gives you options. You can feed into the plug box and connect to one pair of screws, then subfeed the next circuit using the other pair. OR you can separate the circuits so that the top and bottom halves of the plug are either on a separate circuit or one half can be on a switch. The options are there if you want to use them. To separate the top and bottom half you'd need to break away the jumper between the top and bottom halves of the plug.


How can one replace a cabinet hinge?

To replace a cabinet hinge, you must first remove the screws that attach to the door with either a screwdriver or a drill with screw bit. Next you want to remove the cabinet door. Once you have removed the door, remove the hinge from the cabinet. You can then attach a new hinge. A nice tip is to have a partner hold the door while you screw the hinge back in place.


How do you attach an outlet box to a solid concrete wall?

There are a couple of ways. Hardened steel pins can be shot into the concrete. These pins usually have a 1/4 x 20 threads on to which a nut can be applied. The other way and the most common is to carbide drill a hole in the concrete and insert a concrete wall anchor. There are many types of wall anchors so have a look in a hardware store to find the best type that will suit your situation.


Where is the batteries to the Nerf valcon go?

well, if you mean "Vulcan", if you turn the weapon upsidedown, look abit further from the trigger, you will see a little screw isolated to the others as the others are screwed into the sides, not the direct bottom. Unscrew it, pull out the chamber, and the batteries are there.


How far apart do you put screws?

The spacing between screws will depend on the specific application. As a general rule, screws should be evenly spaced along the length of the object being fastened. It is common to space screws every 6-8 inches for most projects.

Related Questions

How can you open a Creative Fatal1ty 1010 mouse?

Lift up the white pads on the bottom. Screws are underneath.


What type of screws are typically used to attach a headboard to a bed frame?

The type of screws typically used to attach a headboard to a bed frame are usually wood screws or machine screws.


What is the purpose of screws?

To attach things together.


What type of screws should be used to securely attach a shelf to a brick wall?

To securely attach a shelf to a brick wall, use masonry screws or concrete screws. These screws are designed to penetrate and hold securely in brick or concrete surfaces.


Where is signal flashers on 1996 Chevy S-10 pickup?

I have a 1997 and mine are underneath the Cig lighters. Take the bottom panel screws out and you should see them. I changed mine with only taking several of the screws out. Good luck!!!!!!!!!!


How do you remove the driver side front door panel on a 1996 Toyota Camry?

just undo all the screws on the door, and when you see those little cover pieces that are an off color from the rest, take a Philips screw driver and pry those off because there are extra screws underneath. Remember to take the cover off the inside door handle, and there will be screws on the bottom of the door panel. Good luck


Where is the starter motor on a vauxhall astra?

at the back of the engine underneath the oil filter. one bolt on the bottom side of starter the top bolt screws in from the gear box side


How can I attach wood to concrete?

To attach wood to concrete, you can use concrete screws, concrete anchors, or a combination of both. Pre-drill holes in the concrete, insert the screws or anchors, and then attach the wood using screws or nails. Make sure to use the appropriate tools and hardware for a secure and durable connection.


How easy is the Under Counter Keyboard Drawer to mount?

The Under Counter Keyboard drawer mounts to any desk or shelf by the folding brackets that attaches underneath. The brackets are already attached, so you only have to attach it with the screws.


How do you remove the ignition switch tumbler on a 1986 dodge lancer 2.5?

Remove the screws on the side of the steering column. Remove the screws underneath the steering column and pull the bottom half of the column down. Slide a pin punch into the hole at the ignition tumbler assembly's bottom. Force the tumbler upwards and pull it out of the steering column.


How can I attach a butcher block top to an island?

To attach a butcher block top to an island, you can use screws or brackets to secure it from underneath. Make sure the island surface is level and clean before attaching the butcher block top. You may also need to apply a food-safe sealant to protect the wood.


How do you replace a fuel pump in a 1995 Mazda miata?

underneath the carpet behind the seats there is an access point. unscrew the screws and lift off the cover. then there is another screwed on cover with two gas lines coming from it. It has about * or so tiny screws in it. these screws are extremely easy to break, so smack them with a hammer first to loosen them. dissconnect the hoses to the top of this cover first, and the little electrical plug thing, and pull it out. the fuel pump is connected to the bottom of this cover.