0
How do you wire from breaker to light fixture 1 to light switch 1 to Light switch 2 to light fixture 2?
If you are asking about typical house hold panel, switches and lights then you would get some 12/2 AWG Romex wire and run it to everything. You want to start your taps from the load end (the lights). Tap your neutral, hot and ground to the light fixture 2.
on switch 2, tap the hot going to the light to the bottom pole of the switch. next take a piece of black wire only and tap it to the top pole of switch 2 and the top pole of switch one. Then tap the hot going to light 1 to the bottom pole of switch one. tap the 3 neutrals together and the grounds together. tap the hot, neutral, and ground to light 1. lay the neutral wire onto the neutral bar in the panel. Lay then ground wire to the ground wire in the panel. Lay the hot wire to the breaker in the panel. Make sure all connections and screws are tight but do not over tighten.
If you do not have good knowledge or in doubt, do not work with any live circuits or in the panel. Electricity kills regardless the voltage or amperage. If you dont know what you are doing call a pro!
What else can I help you with?
Can you connect a wall switch and a light fixture to an existing light fixture?
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
Why does dimmer switch cause ceiling light to make noise?
Dimmer switches control the amount of electricity flowing to the light fixture by rapidly turning the power on and off. This rapid cycling can cause the light fixture to vibrate or emit a buzzing sound, especially if the light fixture is not compatible with the dimmer switch. Upgrading to a dimmer switch designed for the specific type of light fixture can help reduce or eliminate the noise.
What could be the problem if a breaker trips when the light is turned off?
If a breaker trips when the light is turned off, it could indicate a short circuit or an overloaded circuit in the wiring. It could also be due to a faulty breaker or an issue with the light fixture itself. It is recommended to consult a licensed electrician to investigate and resolve the issue safely.
What is a key less light fixture?
A keyless light fixture is a type of light fixture that does not have a key or switch to operate it. Instead, it is typically turned on and off by twisting the bulb itself. It is a simple and easy-to-use lighting option commonly found in closets, attics, and utility rooms.
How is the power wired in a 3-way switch setup where the power source is located at the light fixture?
In a 3-way switch setup with the power source at the light fixture, the power is wired from the circuit breaker to the light fixture, then to the first switch, and finally to the second switch. This creates a loop that allows the switches to control the light fixture from different locations.
Can you connect a wall switch and a light fixture to an existing light fixture?
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
How do you connect an ON-OFF switch to control the light?
To control a light with a switch, the switch has to be connected in series with the light fixture.
How can I replace the kitchen light in my home?
To replace the kitchen light in your home, follow these steps: Turn off the power to the light fixture at the circuit breaker. Remove the old light fixture by unscrewing it from the ceiling. Disconnect the wires from the old fixture. Connect the wires of the new light fixture to the corresponding wires in the ceiling. Secure the new light fixture to the ceiling. Turn the power back on at the circuit breaker and test the new light.
How does a light dimmer switch work to adjust the brightness of a light fixture?
A light dimmer switch works by controlling the amount of electricity flowing to the light fixture. By adjusting the voltage, the dimmer switch can increase or decrease the brightness of the light.
What should the reading at the light switch be when the switch and the light fixture is removed. I had a dimmer switch on that light it went out I checked the volts at the switch they were about 14?
On the "hot"wire that comes from the breaker panel the voltage should be from 115 to 120 volts. This is taken from the "hot" wire to either the neutral or the ground wire. If its not then you have a breaker problem or you are on the wrong scale of the test meter.
How can I add a switch to a light?
To add a switch to a light, you will need to first turn off the power to the light fixture. Then, you will need to run electrical wiring from the light fixture to the location where you want to install the switch. Connect the wiring to the switch and the light fixture following the manufacturer's instructions. Finally, secure the switch in place and turn the power back on to test the switch.
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
What are the differences between a single pole and a double pole light switch?
A single pole light switch controls one light fixture from one location, while a double pole light switch controls one light fixture from two locations.
How does a 3 way dimmer light switch work to control the brightness of a light fixture in a room?
A 3-way dimmer light switch works by adjusting the amount of electricity flowing to the light fixture. This allows you to control the brightness of the light by increasing or decreasing the voltage. The switch has three terminals that connect to the power source, the light fixture, and another switch. By toggling the switch up or down, you can adjust the brightness of the light in the room.
How can I disable a motion sensor light?
To disable a motion sensor light, you can usually locate the switch or button on the light fixture itself and turn it off. Alternatively, you can also disconnect the power source to the light by flipping the circuit breaker or removing the light bulb.
What are the steps to install a wire light fixture in a room?
Turn off the power to the room at the circuit breaker. Remove the existing light fixture. Connect the wires from the new light fixture to the corresponding wires in the ceiling. Secure the light fixture to the ceiling. Turn the power back on and test the light fixture to ensure it is working properly.
