answersLogoWhite

0

gas or electric? gas

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

When leak testing a low pressure chiller the maximum pressure to use is?

When leak testing a low pressure chiller, it is recommended to use a maximum pressure of around 10 psi. This is a safe pressure that can help detect any leaks without risking damage to the chiller components. Always refer to the manufacturer's guidelines for specific pressure recommendations.


Where should the discharge from a rupture disc be piped for venting on a low pressure chiller?

The discharge from a rupture disc on a low-pressure chiller should be piped to a safe location away from personnel and equipment, typically to a designated vent stack or exhaust system. It is essential to ensure that the discharge point is elevated and directed away from any occupied areas to prevent exposure to potentially hazardous materials. Additionally, the venting system should comply with local regulations and safety standards to manage any released substances effectively.


Does wind move from high to low or low to high pressure?

Wind moves from high pressure to low pressure. Air always moves from areas of high pressure to areas of low pressure in an attempt to equalize pressure differences.


Is the low pressure port and the low pressure switch the same thing?

No, the low pressure port and the low pressure switch are not the same thing. The low pressure port is used for connecting a gauge to measure refrigerant pressure in the system, while the low pressure switch is a component that monitors the pressure level and can shut off the compressor to prevent damage.


Is hurricane Isaac low pressure or high pressure?

All hurricanes are low-pressure systems.

Related Questions

What is low pressure and high pressure in water chiller unit?

In regards to a water chiller unit, the terms low pressure and high pressure refer to the compressor, which takes low pressure and compresses it into high pressure gas, which is then turned into a liquid to cool the unit.


When leak testing a low pressure chiller the maximum pressure to use is?

When leak testing a low pressure chiller, it is recommended to use a maximum pressure of around 10 psi. This is a safe pressure that can help detect any leaks without risking damage to the chiller components. Always refer to the manufacturer's guidelines for specific pressure recommendations.


Where is the rupture disc located on a low pressure chiller picture?

The rupture disc on a low pressure chiller is typically located on the refrigerant circuit close to the compressor. It is designed to release pressure in the event of an overpressure situation to prevent damage to the system. The exact location can vary depending on the chiller's design and manufacturer.


Where is the rupture disc located on a low pressure chiller?

the rupture disc is piped off the chiller barrel (evaporator) and will vent the refrigerant outside incase of over pressure of the unit


What is the work of Variable Frequency Drives panel in Chiller Plant?

Vfd is used for maintaing the pressure of whole chiller line.


What is Condenser pressure in absorption chiller?

Condenser pressure in an absorption chiller refers to the pressure within the condenser unit where the refrigerant vapor is condensed into a liquid. It is influenced by the temperature of the cooling medium (usually water or air) used to remove heat from the refrigerant. Maintaining appropriate condenser pressure is crucial for the efficient operation of the chiller, as it affects the overall performance and capacity of the cooling system. High condenser pressure can reduce efficiency and increase energy consumption, while low pressure can lead to inadequate refrigerant flow.


What causes high pressure in chiller system?

dirty coil


How does Back-pressure valve work in dairy production?

Back pressure regulating valve is used in ammonia refrigeration plant to maintain the minimum pressure in the evaporator coils. It helps in preventing ice formation / choke upin the PHE chiller.


How absorption heat pump work as a chiller?

yes


What is the correct suction pressure whin charging a chiller using refrigerant 134a?

926.5


What preventative maintenance do chiller service companies offer?

Preventive maintenance for chiller service companies offer Cleaning, Monitoring pressure and the temperature and then general system testing.


If punctured which hose would empty a scuba tank at a faster rate high pressure hose or low pressure hose?

LOW PRESSURE HOSE: Yes, a low pressure hose. A high pressure hose has a very small diameter opening since it is just used to measure pressure and it is not performing any work. A low pressure hose is used to perform work and has a larger diameter opening so air can move through it.