Hot water tanks
Amps = Watts/Voltage. 4500/240 = 18 amps. You would use a #12 copper wire which is rated at 20 amps. On a hot water tank there is only one of the elements on at a time. The incoming cold water is taken to the bottom of the tank through a pipe inside the tank. When the lower thermostat senses the cold water, the lower element turns on. As you draw hot water from the top of the tank the cooler water from the bottom will rise. When the top thermostat senses the cool water it shuts off the bottom element and turns on the top element. When this water is heated to the tank set point it shuts off and the lower element turns on to heat the rest of the water. When the total tank temperature is at the set point all elements turn off. By using this type of procedure there is always hot water at the top of the tank for use.
Actually, not all of this first answer is correct! A 4500 watt heater will draw around 18.75 amps. However, electric water heaters are considered "continuous loads". This means you can't load it's circuit more than 80%. So a 4500 watt heater circuit must be "sized up" to either a 25 amp or 30 amp circuit. This means that #10 copper wire will also be used. Now, a 3800 watt heater will draw around 15.8 amps. In this case, a 20 amp breaker and #12 copper wire can be used. Always check the heater's nameplate to be certain of it's ratings. The calculation used is correct.
An electric water heater in a hot tank is called an immersion heater and many of those run at 3 kW with a thermostat to control the max temperature. Power showers use a type of water heater that heats the water at the point where it is used, without a tank. They run at 6-8 kW and are also controlled by a thermostat.
Rheem
A gas water heater doesn't use electricity to heat water like an electric water heater does. The electrical connection is typically for powering the ignition system or other electronic components on the gas water heater. The 30 amp breaker with 220 volts is required to safely supply power to these components.
No, and this is a very good energy saving practice.
An electric water heater takes more time to heat water in winter because the incoming water is colder during this season. The heater has to work harder to raise the temperature of the cold water to the desired level, thereby taking longer to heat up the water.
water heater installation water heater leak emergency water heater repair service water heater placement electric water heater installation electric water heater solutions gas water heater solutions
tankless water heaterelectric water heater repairgas water heater repairgas water heater installationselectric water heater installationsAffordable Water Heater Repairemergency electric water heater replacementExpert Tankless, Electric, and Gas
Gas Water Heater RepairGas Water Heater LeakingGas Water Heater Installation Electric Hot Water HeatersTankless Water Heaters Electric Water Heater Leaking
Gas heater & electric heater both are available.
Water Heater, Water Heater Repair or Installation, Gas Water Heater, Electric Water Heater, Hot Water Heater, Tankless Water Heater.
You need to say what voltage the heater is running on (it's different in different countries).
Gas Water Heater Hot Water Heaters Solar Water Heater Electric Water Heater Tankless Water Heater
Gas Water Heater Repair Gas Water Heater Leaking Electric Hot Water Heaters Tankless Water Heaters Electric Installing Tankless Water Heater
Water Heater, Water Heater Repairs, Water Heater Installation , Tank water heater, Tankless Water Heater Installation, Electric Water Heater, Gas Water Heater, Leaking Water Heater.
Water Heater Repair Water Heater Leak Repair Emergency plumber Water heater maintenance Electric Water heater Tankless Water heater
No, an electric water heater does not require a vent for proper operation.
The most efficient electric hot water heater available on the market is the heat pump water heater.