0
What else can I help you with?
Can you install a 240v outlet for a stick welder near your panel if it has slots available for a circuit breaker?
Simple answer is yes. But you need to first determine if your breaker can handle it, not just because you have an empty slot. You have to total up amps being used and check rating for your box. If it can handle it then it is a sinch to install
What is the breaker size for a 10 KVA electric heater?
The breaker size for a 10 KVA electric heater would depend on the voltage it operates at. For example, for a 240V heater, you would need a 41.67 Amp breaker (10,000 VA / 240V = 41.67 A). It is important to consult with a licensed electrician to ensure the correct breaker size and electrical setup for your specific heater.
What size breaker is needed for a 20 kva heat strip?
To determine the appropriate breaker size for a 20 kVA heat strip, you need to calculate the current. For a 240V system, the current is approximately 83.3 amps (20,000 VA / 240V). It’s standard practice to use a breaker rated at 125% of the continuous load, so a 100-amp breaker would be suitable for this application, providing a safety margin. Always consult local electrical codes and a qualified electrician for compliance and safety.
What size wire and breaker for a 7.5 hp motor?
For a 7.5 hp motor operating at 240V, you would typically use a 14-gauge wire and a 40 amp breaker. However, it is best to consult the motor's specifications and the National Electrical Code to determine the exact wire size and breaker needed for your specific setup.
If you install a 30A 240V GFI breaker will this be ok or will the cycles the dryer has prematurely fail the breaker?
Installing a 30A 240V GFI breaker for a dryer should be fine as long as the wiring and dryer itself are compatible with the breaker. The GFI breaker is designed to protect against electrical faults and should not be affected by the cycles of the dryer. Make sure to follow the installation instructions carefully to ensure proper functioning.
What is the maximum voltage capacity of a 240V single pole breaker?
The maximum voltage capacity of a 240V single pole breaker is 240 volts.
What is the maximum current capacity of a 30 amp breaker for a 240v circuit?
The maximum current capacity of a 30 amp breaker for a 240v circuit is 30 amps.
Can you install a 240v outlet for a stick welder near your panel if it has slots available for a circuit breaker?
Simple answer is yes. But you need to first determine if your breaker can handle it, not just because you have an empty slot. You have to total up amps being used and check rating for your box. If it can handle it then it is a sinch to install
What is the recommended AC breaker size for a 240V air conditioning unit?
The recommended AC breaker size for a 240V air conditioning unit is typically 20 amps.
What is the breaker size for a 10 KVA electric heater?
The breaker size for a 10 KVA electric heater would depend on the voltage it operates at. For example, for a 240V heater, you would need a 41.67 Amp breaker (10,000 VA / 240V = 41.67 A). It is important to consult with a licensed electrician to ensure the correct breaker size and electrical setup for your specific heater.
How much voltage should be in 2pole circuit breaker?
In America, a 2-pole breaker is controlling 240V. 120V per leg.
Would a 30A 240V circuit breaker be too large to safely support a either a 20A or 23A 240V bandsaw?
Yes it will operate it fine.
How to test a 240v outlet for proper functionality?
To test a 240V outlet for proper functionality, you can use a multimeter. Set the multimeter to measure voltage and then insert the probes into the outlet's slots. If the reading shows around 240V, the outlet is functioning correctly. If the reading is significantly lower or higher, there may be an issue with the outlet. It is recommended to consult a professional electrician for further inspection and repairs if needed.
What size wire and breaker for a 7.5 hp motor?
For a 7.5 hp motor operating at 240V, you would typically use a 14-gauge wire and a 40 amp breaker. However, it is best to consult the motor's specifications and the National Electrical Code to determine the exact wire size and breaker needed for your specific setup.
If you install a 30A 240V GFI breaker will this be ok or will the cycles the dryer has prematurely fail the breaker?
Installing a 30A 240V GFI breaker for a dryer should be fine as long as the wiring and dryer itself are compatible with the breaker. The GFI breaker is designed to protect against electrical faults and should not be affected by the cycles of the dryer. Make sure to follow the installation instructions carefully to ensure proper functioning.
What voltage is needed for electric ovens?
240V
What is the purpose of a single pole 240v breaker in an electrical circuit?
A single pole 240V breaker is used in an electrical circuit to protect the circuit from overloading and short circuits. It helps to safely distribute electricity and prevent damage to the wiring and appliances connected to the circuit.
