To calculate the wattage of a 200 ampere welding machine, you can use the formula: Watts = Volts × Amperes. If we assume the machine operates at a standard voltage of 230 volts, the wattage would be approximately 46,000 watts (or 46 kilowatts). However, actual wattage can vary based on the efficiency and specific design of the machine. Always check the manufacturer's specifications for precise information.
One watt is equivalent to one volt-ampere (1 W = 1 V × 1 A), meaning that to produce one watt of power, you need a voltage of one volt with a current of one ampere. Therefore, the relationship between voltage, current, and power is described by the formula P = V × I. The specific voltage required for one watt can change depending on the current.
One ampere is equal to one watt in a system with a voltage of one volt. This relationship is defined by Ohm's Law, which states that power (in watts) is equal to current (in amperes) multiplied by voltage (in volts).
An ampere is a unit of charge flow rate, while a watt is a unit of energy flow rate. The two units are not directly convertible. More specifically, one ampere is one coulomb per second, while one watt is one joule per second. If you knew how many volts were involved, you could compare, because volts is joules per coulomb.
The amps drawn by a 65 watt light bulb should be 65/120 or 0.54167. This fraction of an ampere may be restated as 541.67 milli-amps.
Batteries are generally not listed as having watts. And there are a couple of different ampere ratings. But if you're running something needing 12W of a 12V battery it's pulling 1A out of the battery at the moment.
The same number as 250 Oranges is apples. A watt is a volt times an ampere.
To calculate the current you need to take theWatt rating of your welder and divide this by the voltage youhave setthe machine at- this gives the amperage. So for a 1440 watt welder running at 12v the current would be: 1440 watt/ 12v = 120 Amps
Watt = ampere x volt. So if you know the voltage, you can convert amperes to watts or vice versa. If not, you don't have enough information.AnswerThe ampere hour (A.h) is a unit of measurement for electric charge (the SI unit being a coulomb). The watt hour (W.h) is a unit of measurement for electrical energy (the SI unit being a joule).In the case of cells and batteries, if you multiply its capacity (in ampere hours) by the voltage, then you'll have its capacity in watt hours.
One watt is equivalent to one volt-ampere (1 W = 1 V × 1 A), meaning that to produce one watt of power, you need a voltage of one volt with a current of one ampere. Therefore, the relationship between voltage, current, and power is described by the formula P = V × I. The specific voltage required for one watt can change depending on the current.
That's like asking how many meters in a liter. Ampere and Volt are two DIFFERENT measurements. Ampere is how much electricity you are using, while volts are how much pressure the electricity is under(Think water). If you want to figure out how many amperes your appliance is using you could use this formula: P=UxI (Watt=Volt x Ampere) or U=RxI(Volt=Resistance x Ampere).
Watts (or kilowatts) and amperes are used to measure different things. Watts is a unit of power; ampere is a unit of current. The relationship (for direct current) is: watt = ampere x volt For AC, the relationship is a bit more complicated: watt = ampere x volt x power factor However, the power factor is often close to one.
One ampere is equal to one watt in a system with a voltage of one volt. This relationship is defined by Ohm's Law, which states that power (in watts) is equal to current (in amperes) multiplied by voltage (in volts).
over 9000!
The same number as 250 oranges is apples. A watt is a volt times an ampere.
In SI, the coulomb is a special name given to an ampere second, in much the same way that a watt is a special name for a joule per second.
An ampere is a unit of charge flow rate, while a watt is a unit of energy flow rate. The two units are not directly convertible. More specifically, one ampere is one coulomb per second, while one watt is one joule per second. If you knew how many volts were involved, you could compare, because volts is joules per coulomb.
The answer is volt.