0
What else can I help you with?
How many watts does it take to heat 700 square feet?
The wattage required to heat 700 square feet depends on factors like insulation, ceiling height, and climate. A general rule of thumb is to use about 10 watts per square foot for heating, which would mean approximately 7,000 watts for 700 square feet. However, this can vary, so it's best to consult with a heating professional for a more tailored assessment based on specific conditions.
How many watts is 2000rms watts?
2000 watts RMS is equivalent to 2000 watts. RMS (Root Mean Square) is a method used to measure the power of an electrical signal.
How do you convert arms to watts?
To convert arms (root mean square current) to watts (power), you need to know the voltage in the circuit. The formula for this conversion is: Power (W) = Current (Arms) x Voltage. Multiply the root mean square current (Arms) by the voltage in the circuit to get the power in watts.
How many watts does it take to heat 200 square feet?
If you tell us the starting temperature and the finishing temperature and the specific heat of the material this 200 sq ft is made of then we'd have a chance of answering this one. But let's say that you're talking about a room (you didn't say you were but let's assume this), then a rule of thumb calculation, where the assumption is made that it takes 10 watts to heat a square foot of room, would show that you'd need 2,000 watts.
How do you determine watts per square foot and total volt amp?
For lighting using CFL bulbs you can use 10 square feet per watt. The volt-amps is the volts times the amps, or the watts divided by the power factor. Most CFL bulbs are marked with the voltage and the current.
How many watts are required to heat a room of 100 square feet?
To heat a room of 100 square feet, approximately 10,000 watts of power are required.
How many square miles is Watts California?
Watts, CA is 2.12 square miles.
How many kwh does a 52800 square foot building use in the summer?
For lighting use 0.1 watts of CFL per square foot, so 5-6 kW. In the summer, nothing for heating.
How many watts does it take to heat 700 square feet?
The wattage required to heat 700 square feet depends on factors like insulation, ceiling height, and climate. A general rule of thumb is to use about 10 watts per square foot for heating, which would mean approximately 7,000 watts for 700 square feet. However, this can vary, so it's best to consult with a heating professional for a more tailored assessment based on specific conditions.
how many watts are required to run a craftsman 60,000 btu propane forced air heater?
The conversion factor of 1 BTU = 0.293 watts. So, 60,000 * 0.293 watts = 17,580 watts. 17580 watts are required to run a craftsman 60,000 btu propane forced air heater.
A total of 3500 square feet of occupied area the minimum number of 15-ampere lighting branch circuits is?
To determine the minimum number of 15-ampere lighting branch circuits required for a 3,500 square foot occupied area, you can refer to the National Electrical Code (NEC). Typically, one 15-amp circuit can handle up to 1,500 watts of lighting. Assuming a general guideline of 3 watts per square foot for lighting, you would need approximately 11,667 watts for 3,500 square feet, which translates to about 8 circuits (11,667 watts ÷ 1,500 watts per circuit). Thus, a minimum of 8 lighting branch circuits is recommended.
How many watts are required to heat one gallon of water one degree?
2.4705 watts/hour
What is the area of Watts Bar Lake?
The area of Watts Bar Lake is 157.827 square kilometers.
What is the required power output, measured in watts, for a well pump to operate efficiently?
The required power output for a well pump to operate efficiently is typically measured in watts.
How many watts is 2000rms watts?
2000 watts RMS is equivalent to 2000 watts. RMS (Root Mean Square) is a method used to measure the power of an electrical signal.
How many watts are required to start a car?
The average car requires about 400 to 600 watts of power to start.
What is required input in watts to operate an 80 percent efficient 5 hp electric motor?
To answer this question a voltage must be stated. W = A x V x pf.
