answersLogoWhite

0

Divide the power rating (in watts) by the voltage (in volts). So if you use a 100 watt light bulb in a typical 110 volt lamp then it will draw 100/110 = .91 amps of current. Or plug a 1500 watt electric heater into a 110 volt wall socket and it will draw 1500/110 = 13.6 amps of current.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

How many amps does a dewalt compressor draw?

The amp draw of a DeWalt compressor can vary depending on the model and specifications. However, most DeWalt compressors for residential use typically draw between 10-15 amps. It's important to check the specific model's manual or specifications for accurate information.


What is your amp draw of a mr16 light with a transformer?

The amp draw of a MR16 light with a transformer can vary depending on the wattage of the light bulb and the efficiency of the transformer. Typically, a 50 watt MR16 halogen bulb with a transformer can draw around 0.42 amps. It is important to check the specifications of your specific MR16 light and transformer to determine the exact amp draw.


Can you connect a 230 volt 15 amp air compressor to a 240 volt 50 25 amp generator?

No, it is not safe to connect a 15 amp air compressor to a 25 amp generator. The generator's output exceeds the maximum amperage of the air compressor, which could potentially damage the compressor or cause overheating. It is recommended to use a generator that matches the power requirements of the air compressor for safe operation.


What is the maxamin voltage you can draw from a 32 amp socket?

The maximum voltage you can draw from a 32 amp socket depends on the voltage rating of the socket. For example, if it is a standard 240-volt socket, the maximum voltage you can draw is 240 volts. It's important to check the voltage rating of the socket to ensure you are not exceeding its limits.


How much electricity does an average bathroom fan use compared to a dehumidifier?

A dehumidifier is pretty much the same device as an air conditioner. It has a compressor which uses freon to create a cold surface for water to condense on. The fan only is a simple fan that moves air. The fan is the smallest electrical draw as opposed to the dehumidifier. The fan can have a current draw of as little as 1/10 of an amp when the dehumidifier can have a current draw as much as 15 amps when the compressor is running.

Related Questions

How can you test a compressor to see if it has shorted?

You would need to put an amp-meter on the circuit to see what the current draw is like. ====== If the compressor is shorted to ground you cannot check the amp draw because it will constantly kill the circuit breaker. A better way to go would be to check the continuity of the compressor to ground and each winding.


How many amps does a dewalt compressor draw?

The amp draw of a DeWalt compressor can vary depending on the model and specifications. However, most DeWalt compressors for residential use typically draw between 10-15 amps. It's important to check the specific model's manual or specifications for accurate information.


How do you check for amp draw with volt meter on automobile?

you dont you need an ammeter for that


When central air is running lights flicker?

The lights are flickering Due to a high starting amp draw created by the compressor starting. This may be a problem starting with the compressor or maybe rectified by adding a hard start kit to the compressor circuit to reduce the starting amp draw. However there can be several reasons for the high amp draw. Some of the problems can be... Over charge of refrigerant, a capacitor that is getting weak, not enough delay between cycles, loose wires or bad connections or a compressor that is in the first stage of failing. In any case the charge should be properly checked and a hard start kit should be added.


How do you tell if the compressor is bad in a window air conditioner?

Borrow a clamp on amp meter and check full load amps. If pulling full load amps then compressor condemned.


1 hp compressor amp?

To answer this question the voltage of the compressor is needed.


How do you test a compressor?

To test a compressor if locked up read the tag on compressor for locked rotor amps, then bypass safety therm-o-switch found under protective black cover on compressor, and with a clamp-on amp meter momentarily run compressor to check amperage.


What is your amp draw of a mr16 light with a transformer?

The amp draw of a MR16 light with a transformer can vary depending on the wattage of the light bulb and the efficiency of the transformer. Typically, a 50 watt MR16 halogen bulb with a transformer can draw around 0.42 amps. It is important to check the specifications of your specific MR16 light and transformer to determine the exact amp draw.


Can you connect a 230 volt 15 amp air compressor to a 240 volt 50 25 amp generator?

No, it is not safe to connect a 15 amp air compressor to a 25 amp generator. The generator's output exceeds the maximum amperage of the air compressor, which could potentially damage the compressor or cause overheating. It is recommended to use a generator that matches the power requirements of the air compressor for safe operation.


How do you rest a 60a Air Conditioner Disconnect?

There is no reset on the disconnect, you will need to check the fuse's at the disconnect and replace the on that is bad. But most likely if you blew a 60 amp fuse you have a short somewhere, check your termanals at the compressor to see if the compressor went to ground.


What happens to amp draw as static pressure increases?

As your static pressure increases your Amp draw will drop


Can you power 100volt compressor with 400watt inverter?

It depends on the draw of the compressor.