answersLogoWhite

0

If you are talking about a breaker in a house panel then a 15 amp breaker would be used. It is the smallest amperage breaker that you will find in a house panel.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

How does a circuit breaker use an electromagnet?

The electromagnet in the circuit breaker is used for instantaneous tripping if short-circuit condition arises. At defined current level the electromagnet develops the force high enough to cause the tripping of the mechanism.


Would replacing an old 15 amp breaker stop the air conditioner and fan from throwing the breaker?

What size is the AC? Look at the power consumption rating of the AC unit; if it pulls anything close to 15 amps, a new breaker will not solve your problem. There should be an information panel that shows the current draw of the AC. If the AC pulls more than the breaker can handle, you need to re-wire the outlet for the AC. You can't safely just replace the breaker with a larger one since that would result in a fire hazard.


How a circuit breaker prevent from too much current flowing into device?

The current (in question) flows through both the circuit AND the circuit breaker [they are in series]. Within the circuit breaker when the current exceeds the preset limit it will open the circuit thus stopping all current flow. There are two common ways of doing this 1) magnetism - a coil pulls a switch open 2) thermal - a bimetallic strip bends away from its contacts, which opens the circuit.


Can circuit breakers help to prevent building fires?

Breakers limit the current on the conductor to a safe level, too many appliances plugged in. You trip a breaker, hopefully you then transfer load to another circuit. Breakers use two different methods to accomplish this, one uses a bimetallic strip and the current passes directly through, too high a current causes the strip to deflect. It acts on a mechanism much like the sear in a guns trigger, the deflection pulls the trigger causing a spring to open the contacts and turn off the circuit. Another type is thermal magnetic, current passing through the breaker causes a magnetic field to act on a coil tripping the breaker. When breakers are wired and work properly they prevent fires!Bending metal opens a switch


What size breaker do i need for a central heat and air unit?

The breaker type be it a single pole or double pole will depend on what voltage the air conditioner operates on. Once the voltage is established, the sizing of the breaker depends on what the current draw of the air conditioner is.

Related Questions

What can you do if you're newly installed dryer keeps tripping the electrical panel repeatadly and it also trips the GFI in the Garage at the same time?

If the GFI that is tripping is a different circuit, there is electrical leakage between the circuit the GFI is controlling, and the dryer circuit. It is possible that there is some cross wiring in the electrical box. I would strongly recommend getting a licensed electrician to look at it, preferably before you have a fire. If the GFI is the same circuit as the one where the dryer is plugged in, you might want to have the dryer checked for leakage to ground. You should also check the dryer circuit's rating against the rating of the breaker in its circuit. A dryer typically takes 30A on usually a single two-gang breaker; if you have a larger dryer that pulls, say, 45A, a 30A breaker will always pop. It sounds to me like a bad electrician has, instead of buying a proper two-gang 30-A breaker, installed your dryer across two circuits, one being the garage GFI circuit; the dryer, because it pulls 220V, pulls an unbalanced load across the GFI and triggers it, and the other circuit breaker is triggered because it loses the extra power provided through the GFI. I cannot emphasize this enough: get this checked out and fixed. Now. Before you get a house fire.


What size amp circuit breaker should be used for a geyser?

The size of the amp circuit breaker needed for a geyser will depend on the specific electrical requirements of the geyser. It is important to consult the geyser's manufacturer specifications to determine the appropriate amperage for the circuit breaker. Typically, a 20-amp circuit breaker is commonly used for residential geysers, but larger geysers may require a higher amperage circuit breaker. It is crucial to ensure that the circuit breaker is properly sized to prevent electrical hazards and ensure safe operation of the geyser.


How does a circuit breaker use an electromagnet?

The electromagnet in the circuit breaker is used for instantaneous tripping if short-circuit condition arises. At defined current level the electromagnet develops the force high enough to cause the tripping of the mechanism.


What size amp circuit breaker do you use on a 55 watt fluorescent light?

A 55 watt fluorescent light only pulls 0.4 amps. Lights can be installed on a 15 amp breaker using 14/2 wire. A maximum of 1440 watts is all that is allowed on a 15 amp circuit.


Would replacing an old 15 amp breaker stop the air conditioner and fan from throwing the breaker?

What size is the AC? Look at the power consumption rating of the AC unit; if it pulls anything close to 15 amps, a new breaker will not solve your problem. There should be an information panel that shows the current draw of the AC. If the AC pulls more than the breaker can handle, you need to re-wire the outlet for the AC. You can't safely just replace the breaker with a larger one since that would result in a fire hazard.


How a circuit breaker prevent from too much current flowing into device?

The current (in question) flows through both the circuit AND the circuit breaker [they are in series]. Within the circuit breaker when the current exceeds the preset limit it will open the circuit thus stopping all current flow. There are two common ways of doing this 1) magnetism - a coil pulls a switch open 2) thermal - a bimetallic strip bends away from its contacts, which opens the circuit.


How do you reset the circuit breaker on the outside junction box of a central air conditioning system?

a disconnect? if its a switch, turn it all the way off... then all the way on. if it pulls out and has fuses then be sure they work and stick it back in. or it could be that the breaker inside has been tripped. then you would turn it off then on.


What is the job of the power source in the circuit?

it pushes and pulls the electrons trough the circuit


Can circuit breakers help to prevent building fires?

Breakers limit the current on the conductor to a safe level, too many appliances plugged in. You trip a breaker, hopefully you then transfer load to another circuit. Breakers use two different methods to accomplish this, one uses a bimetallic strip and the current passes directly through, too high a current causes the strip to deflect. It acts on a mechanism much like the sear in a guns trigger, the deflection pulls the trigger causing a spring to open the contacts and turn off the circuit. Another type is thermal magnetic, current passing through the breaker causes a magnetic field to act on a coil tripping the breaker. When breakers are wired and work properly they prevent fires!Bending metal opens a switch


What size breaker do i need for a central heat and air unit?

The breaker type be it a single pole or double pole will depend on what voltage the air conditioner operates on. Once the voltage is established, the sizing of the breaker depends on what the current draw of the air conditioner is.


How many recessed lights can you put on a 20 Amp circuit breaker?

If there is nothing else on the circuit then you could easily install 15. If there are outlets on the same circuit then try and keep the total of outlets and lights to a maximum of 15. But in reality the number of devices depends on how many amps each device pulls. Add up the amperage of the recessed lights you are going to install and then add any outlets and what may be plugged into them to get the number you can install. A 100 watt light bulb will draw about 1 amp. So you can easily have 15 on a 20 amp circuit.


What is a power sources job?

it pushes and pulls the electrons through the circuit