0
It is typically accepted to be 440 to 500, based on 110 to 125V for common power outlets.
This is based on experience in the USA with 60Hz power supplied by utility companies.
Since 3-phase is mentioned, you should also state if this is delta or wye configuration, and whether you are measuring from phase to phas or phase to neutral.
For a more competent answer, an electrician should refine this answer, or you could look up the relevant standard, probably an ANSI standard.
What else can I help you with?
Can you run a 570 volt motor on 480 volt three phase power supply?
No, it is not recommended to run a 570 volt motor on a 480 volt power supply. The motor is rated for a specific voltage to ensure optimal performance and prevent damage. Running the motor at a lower voltage could result in overheating and premature failure.
What is the benefits of using 277 volt electrical equipment?
with 3 phase lighting you do not have to use as large of wire and can use one neutral for every 3 current carrying conductors so it cut down on material costs ( as voltage increases current decreases) <<>> The voltage 277 is the star-point voltage of a 480 volt three phase system. By using a 480 volt wye system you have the dual ability of running 480 volt three phase equipment along with 277 volt lighting. The side advantage is the ability of using the phase voltage to ground (neutral) 480 / 1.73 = 277 volts for general lighting of the building the 480 volt equipment is located in.
What is the total of a phase to earth voltage on 11000 volts?
An 11,000 volt three-phase supply has a voltage of 6351 from live to neutral, when there is a neutral wire.
How do you obtain a 230 volts single phase supply from a 400 volts three phase four wire supply?
400 volt three phase on a grounded system is 230 volt single phase, with each phase 120 degrees apart. So, if you have a 400 volt, three phase four wire service (grounded service), you can pull one phase off and reference to the neutral for 230 volt service. Note this may not allow 115 volt service, unless there is also a center tap for each phase.
How many volt each phase in three phase?
600 volts between any two wires. The phase has nothing to do with voltages, only current relationship.
In a three phase four wire wye system having 277V for lighting the three phase motors operate on what voltage?
480 Volt
What transformer do you need if you have primary voltage of 600 3 phase and require 240 volt 1 phase?
A single phase 600 to 240 Volt transformer using two phases of the three phase primary.
Can you connect a 277V ballast to 208V line service?
No. A 277 volt ballast needs the correct voltage to operate. The 277 voltage is derived from the star point voltage of a 480 volt three phase system (277/480). The 208 voltage is a three phase line voltage whose star-point voltage is 120 volts (120/208).
What is voltage phase to phase 380 3 phase?
Voltage phase to phase in a 380V 3-phase system refers to the voltage measured between any two of the three live conductors in the system. In a balanced 3-phase system, the phase to phase voltage is equal to the line voltage, which is 380V in this case. This voltage is commonly used in industrial and commercial applications to power heavy machinery and equipment. It is important to note that the phase to phase voltage is higher than the phase to neutral voltage in a 3-phase system.
What is the voltage for Sweden?
Outlet for standard electronics is 230 Volt , 50HzThe master feed into Swedish houses is 400 Volt three-phase , 50Hz.When 400 Volt three-phase is split in three single phases it becomes threesingle 230 VoltBigger appliances , e.g Washing-machines, dryers, stoves, used to be400 Volt three-phase, but nowadays most washing-machines and dryersare built for 230 Volt single-phase.
Can you run a 570 volt motor on 480 volt three phase power supply?
No, it is not recommended to run a 570 volt motor on a 480 volt power supply. The motor is rated for a specific voltage to ensure optimal performance and prevent damage. Running the motor at a lower voltage could result in overheating and premature failure.
What is the benefits of using 277 volt electrical equipment?
with 3 phase lighting you do not have to use as large of wire and can use one neutral for every 3 current carrying conductors so it cut down on material costs ( as voltage increases current decreases) <<>> The voltage 277 is the star-point voltage of a 480 volt three phase system. By using a 480 volt wye system you have the dual ability of running 480 volt three phase equipment along with 277 volt lighting. The side advantage is the ability of using the phase voltage to ground (neutral) 480 / 1.73 = 277 volts for general lighting of the building the 480 volt equipment is located in.
Can you run a three phase appliance on 240 volt power supply?
No. You need a 3-phase supply that matches the voltage and current rating of your appliance.
What is the total of a phase to earth voltage on 11000 volts?
An 11,000 volt three-phase supply has a voltage of 6351 from live to neutral, when there is a neutral wire.
What is the voltage of a 3 phase 4 wire 277 volt lighting circuit?
The voltage of 277 volts is the wye of a three phase 480 volt system. Just as the voltage of 347 is the wye voltage of a three phase 600 volt system. To obtain these voltages for any three phase system, take the three phase voltage and divide it by 1.73. 480/1.73 = 277 volts, 600/1.73 = 347 volts.
In a 3 phase 480 panel what voltage should you get phase to phase?
The voltage you are referring to is a 'line-to-line' voltage ('line voltage'), as there is no such thing as a 'phase-to-phase' voltage.480 volts. In real life, the voltage will vary slightly by up to 3% (14 V) on a properly sized circuit. Line to neutral will measure 277 volts, plus or minus 3%.
What is the difference between single phase and three phase voltage measurement?
Phasing, or the number of phases in an electrical system has nothing to do with the voltage. A single phase and three phase supply could have a voltage supply of any given voltage from virtually 0 to infinity. Most single phase power supplies in the US are 120/208-240 volt. Three phase power supplies are typically 120/208 to 277/480 volt.
