answersLogoWhite

0

First, get a tasteful wrapping paper and a bow ... just kidding.

If you don't have one of those dandy little reels, then the proper way is to coil. Hold your left hand out, palm up. Hold one end of the extension cord between your thumb and palm with the loose end beyond your thumb. With your right hand, measure out about 3 feet or so and loop it around your left hand just like you would think is correct.

Now comes the tricky part to get used to: do the same thing again, but let the loop go the other direction -- the cord will naturally want to do this. Repeat this over-and-under pattern until you have coiled the whole thing.

It sounds like a pain to re-learn, but try it with two extension cords. Take the first one and do it the way you thought was correct before -- looping over then over again -- and the other one using the above steps. Take the first one and try extending it by holding one end and tossing the coil across the yard. Now try it with the new coiling method.

Big difference, eh? This is how sailors coil mooring lines. It works with garden hoses and ropes as well.

DON'T wrap cords around your elbow and hand. It causes the wires to twist inside the insulation and causes undue wear on the cord. You may also want to tie a length of thick twine to one end of the extension cord to keep the coil neat when transporting it.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

Is wrapping two electrical cords with cling wrap and nonelectrical tape a fire hazard?

The method you describe could cause you problems and in certain circumstances could cause a fire. In connecting a severed extension cord back together again the purpose is to bring the insulation value back to its original value. The severed cord ends should cut back to expose the conductors. The proper connecting device should be a "crimp butt splice" sized to fit your wire size of the cord. Stagger these splices along the wires you are reconnecting so they are not parallel to each other and create a large lump in the cord. Over these splices a rubber amalgamating tape should be used to fill the voids around the wires and to bring the diameter back to the original outer diameter to the cord. Over the rubber tape should be wound PVC electrical tape. Double wrap the tape from one end of the splice to the other end of the splice and back again. This repair will give you many more years of service from the cord with out any problems.


Measure chest size?

To measure your chest size, wrap a tape measure around the fullest part of your chest, typically right under your armpits. Make sure the tape measure is straight and parallel to the ground for an accurate measurement. Record the measurement in inches or centimeters for sizing reference.


How do you tape an elbow injury?

To tape an elbow injury, first clean and dry the area. Then apply a protective underwrap if desired. Use sports tape or kinesiology tape to wrap around the elbow, providing support and stability while allowing for proper movement. Make sure the tape is snug but not too tight to restrict circulation.


How do you make a single negatve pole electro magnet?

Wrap copper wire around a nail, then attach the ends of the wire to a D battery with tape to make an electromagnet.


How do you measure a womans butt?

Measuring a woman's butt can be done by using a flexible measuring tape to measure the circumference of the widest part of her hips or buttocks. Start at one hip bone, wrap the measuring tape around the body, and compare the measurement to standard sizing charts if needed.

Related Questions

Is wrapping two electrical cords with cling wrap and nonelectrical tape a fire hazard?

The method you describe could cause you problems and in certain circumstances could cause a fire. In connecting a severed extension cord back together again the purpose is to bring the insulation value back to its original value. The severed cord ends should cut back to expose the conductors. The proper connecting device should be a "crimp butt splice" sized to fit your wire size of the cord. Stagger these splices along the wires you are reconnecting so they are not parallel to each other and create a large lump in the cord. Over these splices a rubber amalgamating tape should be used to fill the voids around the wires and to bring the diameter back to the original outer diameter to the cord. Over the rubber tape should be wound PVC electrical tape. Double wrap the tape from one end of the splice to the other end of the splice and back again. This repair will give you many more years of service from the cord with out any problems.


How do I properly wrap bar tape on my bicycle handlebars?

To properly wrap bar tape on your bicycle handlebars, start at the end of the handlebar and wrap the tape in a spiral pattern, overlapping each wrap slightly. Make sure to keep the tape taut as you wrap to prevent it from unraveling. Finish by securing the end of the tape with electrical tape or the provided bar end plug.


What is the safest way to cover electrical wires?

sodler it and then wrap it in electeic tape


How can I properly wrap drop bars for my bicycle?

To properly wrap drop bars on a bicycle, start by securing the end of the bar tape with electrical tape. Wrap the tape in a spiral pattern, overlapping each layer slightly. Make sure to keep the tape taut and smooth as you go. When you reach the end of the handlebar, secure the tape with more electrical tape. Trim any excess tape and make sure the ends are neat.


How do I properly wrap handlebar tape on my bike?

To properly wrap handlebar tape on your bike, start at the end of the handlebar and wrap the tape in a spiral pattern, overlapping each layer slightly. Make sure to pull the tape tight as you go to ensure a secure fit. Finish by securing the end of the tape with electrical tape or the provided finishing tape.


How do you properly wrap bar tape for a bicycle handlebar?

To properly wrap bar tape for a bicycle handlebar, start at the end of the handlebar and wrap the tape tightly in a spiral pattern, overlapping each layer slightly. Make sure to keep the tape taut and smooth out any wrinkles as you go. Finish by securing the end of the tape with electrical tape or a finishing plug.


How can I properly wrap handle bars on a bicycle?

To properly wrap handlebars on a bicycle, start by removing the old tape and cleaning the handlebars. Begin wrapping from the end of the handlebars, overlapping the tape slightly as you go. Make sure to keep the tape tight and smooth as you wrap. Finish by securing the end of the tape with electrical tape or a finishing plug.


What is the best method for securing rim tape using electrical tape?

The best method for securing rim tape using electrical tape is to wrap the electrical tape tightly around the rim, ensuring that it covers the entire rim tape and is securely fastened in place. This will help prevent the rim tape from shifting or coming loose during use.


What kind of tape do you need to tape your colorguard rifle?

Strapping tape to go around your tip, bolt, and butt. And then my guard uses electrical tape to wrap around the entire thing


Where can I purchase the cheapest extension cords?

Shrink wrap film is good enough to wrap small boxes. It provides protection from the elements. That is an addead peace of mind whether you are shipping those boxes or keeping them in a storage.


How can I properly wrap road bike handlebar tape for a professional and comfortable finish?

To properly wrap road bike handlebar tape for a professional and comfortable finish, start at the end of the handlebar and wrap the tape in a spiral pattern, overlapping each wrap slightly. Make sure to keep the tape tight and smooth as you go. Finish by securing the end of the tape with electrical tape or bar-end plugs. This will provide a clean and comfortable grip for your hands while riding.


How can I properly re-tape handlebars on a bicycle?

To properly re-tape handlebars on a bicycle, start by removing the old tape and cleaning the handlebars. Begin wrapping the new tape from the end of the handlebars, overlapping each wrap slightly. Make sure the tape is tight and smooth as you wrap it around. Finish by securing the end of the tape with electrical tape or a finishing plug.