0
The standard units were 220 volt, 3 phase. 220 single phase was a purchase option. There were also conversion kits to convert the machines from 3 phase to single phase. The kits contained a 1 HP 220 volt capacitor start motor and a DC motor brake control assembly.
Jerry S
greentron@att.net
What else can I help you with?
How do you change out an harmonic balancer on a 1993 Mercury Topaz?
Big job! The motor has to be lowered to get at the bolt to take it off. If you have a welder I would just notch out a square in the inner fender well to get the wrench in. Then just use a rubber peice from a floor mat to keep the water out. Other than that its a peice of cake. Take the belt off, one bolt , take it off put new one on and tighten New bolt. Big Job indeed! You have to remove the upper left motor mount while you are supporting the engine. Then you have to remove both lower engine mounting plates which are located under the radiator. Disconnect the two front stabilizer mounts when you are down there too. Remove the two plates and slowly drop the engine to where you can see the Harmonic balancer bolt. Put a 21 MM socket on it and hit it with decent impact gun removing the bolt. Next see if you have enough room to extract the pully. I did not have enough room and ended up cutting about 1/2 inch of metal from the inner wheel well. Next put on a puller and take off the pully. Mine was on very tight and I needed a good puller. Take your time it can be done and The GL on the back of the car mean Good Luck because you will need it. My car was the 3.0 v-6
What are some DIY spinning wheel plans that I can use to create my own spinning wheel at home?
Some DIY spinning wheel plans that you can use to create your own spinning wheel at home include the Saxony wheel, the castle wheel, and the Norwegian wheel. These plans can be found online or in spinning wheel crafting books.
What is the purpose of a measuring wheel?
A surveyor's wheel, also called a clickwheel, hodometer, waywiser, trundle wheel, measuring wheel, or perambulator is a device for measuring distance.
What kind of wheel is used to measure long distances?
A measuring wheel, also known as a surveyor's wheel or clickwheel, is typically used to measure long distances. It consists of a wheel attached to a handle, connected to a counter that records the number of rotations made by the wheel. By rolling the wheel along the ground, users can accurately measure distances.
How can I set up a spinning wheel for a game or activity?
To set up a spinning wheel for a game or activity, you will need a wheel with sections labeled with different prizes or outcomes, a sturdy base to hold the wheel upright, and a mechanism to spin the wheel such as a peg or handle. Simply assemble the wheel on the base, ensure it spins freely, and then you're ready to play!
Where can you find a transformer for a Nortron 7300 wheel balancer?
Call 502 5538210 we have a spare transformer for 190.00
How do you calibrate a nortron 7402-116 wheel balancer?
To calibrate a Nortron 7402-116 wheel balancer, first ensure that the machine is on a level surface and powered on. Next, select the calibration mode using the machine's control panel, then follow the prompts to input the required parameters, which may include wheel size and weight. Place a test weight on the balancer as instructed, and allow the machine to perform the calibration process. Once complete, confirm that the displayed values are accurate and adjust if necessary, following the manufacturer's guidelines.
Where to get a manual for your Nortron 7300-116 wheel balancer?
To obtain a manual for your Nortron 7300-116 wheel balancer, you can check the manufacturer's official website for downloadable resources or contact their customer support for assistance. Additionally, online forums and automotive equipment retailers may have user manuals or guides available. If you prefer physical copies, searching on websites like eBay or Amazon might yield options as well.
Where to place weights on wheel?
you need a wheel balancer for that
How do you replace the harmonic balancer on a 1993 buick cenyury?
You will need to go through the passenger front wheel well (wheel off). Remove belt, remove pulley/balancer with a balancer puller tool. Air tools make this job MUCH easier.
Has anyone heard of a fmc wheel balancer series 7?
Is made by snap on and is usually a john bean balancer with FMC name on it
After i calibrate my fmc 5800 wheel balancer. it comes up RPG lo it wont run why help?
when i calibrate my FMC wheel balancer i only get cal o not cal good at the end
Where can hunter wheel balancer parts?
Hunter wheel balancer parts can be found by doing a simple key word search of the specific balancer online. You may also be able to find a second hand dealer locally that caters to mechanics needing parts and sells parts wholesale.
Where is the sensor on FMC 4100 wheel balancer?
The sensor on the FMC 4100 wheel balancer is typically located at the base of the machine, near the wheel assembly. It is designed to detect the imbalance in the wheel by measuring vibrations as the wheel rotates. This information is then used to determine the necessary weight placements for proper balancing. For specific details, refer to the user manual or manufacturer's documentation.
What does code lpg lo mean on a computerized wheel balancer?
It is low of Liguified petroleum gas, top it up
Crankshaft Pully removal on a 350 Chevy motor?
If your refuring to the harmonic balancer use a good steering wheel puller!!!!
What is the price range for a wheel balancer kit?
Wheel balancing machines can run from $700 - $1,000 and up. There is no wheel balancing kit, but most tire shops will use their machine to balance your wheels at a fairly low cost.
