0
Yes, there are two common types of 4-prong dryer plugs: NEMA 14-30 and NEMA 14-50. The NEMA 14-30 plug is used for dryers that require 240 volts and 30 amps, while the NEMA 14-50 plug is used for dryers that require 240 volts and 50 amps. It is important to use the correct plug type for your specific dryer.
What else can I help you with?
Does it matter how you plug in - are the two prong different?
For most standard two-prong plugs, there is no difference in which prong goes into which outlet. The prongs are typically the same size and shape, so it does not matter which way you plug it in. However, if the plug is polarized (one prong is wider than the other), make sure to plug it in the correct way according to the outlet.
Why wouldn't a 2 prong plug fit in a 3 prong outlet?
The reason might be a voltage or amperage mismatch between the two devices. Plugs and receptacles are matched sets depending on the voltage and the amperage of the devices. The configurations are done in this manor to prevent the wrong voltages being applied to wrong plug in equipment.
Is there any conversion plugs to go from a 4 prong 240 volt dryer outlet to a 3 pronged dryer wire?
for USA, Canada and countries running a 60 Hz supply service.Well, yes, and no. You CAN'T just disconnect the wires from the 60 amp outlet and connect them to three 20 amp outlets. It would be more like tearing out and rebuilding than converting. The 240 volt outlet has a hot wire from each side of the breaker box and each can supply a series of standard outlets if you replace the 60 amp breakers with 20 amps and pull 12 gauge wires.Actually you CAN just disconnect the wires and connect several 20 amp outlets, IF you change the breaker to a 20 amp one. The breaker/fuse has to be sized for the lowest current link, in this case it is not the wire but the outlets. The wire will be oversized but it does not need to be replaced. Some older dryer circuits also did not include a ground, so you will have to run a grounding wire or install a GFI.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Can you change the wall outlet to fit a 4 prong dryer outlet?
It's probably more difficult than you might expect. I'm assuming you have a NEMA 5-15R outlet, and you want to plug in a dryer that has a NEMA 14-30P plug at the end of its electric cable. The NEMA 5-15R outlet is by far the most common type of outlet in North America. It has two flat slots (hot and neutral), and a round safety ground hole. It is rated for 15 A and 125 V. On the other hand, most electric clothes dryers have an electric cable with a NEMA 14-30P plug on the end. It has two flat slots (2 hots from 2 different phases, each one 120 V from neutral, and each one rated at 30 A), an L slot (neutral), and a round safety plug. It is possible for an electrician to "fish" a electric cable carrying the necessary phases through the wall from the fuse box to that outlet, and then pull the old outlet and install a new outlet. If one merely did that last part -- pulled the old outlet and placed a new outlet -- without the proper electrical cables in the wall behind it, then the dryer would probably blow the fuse at the fusebox every time it was turned on.
Can you convert a gas dryer 120V hookup to an electric dryer 240V hookup?
Chances are there is more than 1 outlet connected to the 110volt circuit you are looking to convert. So therefore the easy answer is No. The 240volt dryer circuit must be a dedicated single circuit for the dryer only.
Does it matter how you plug in - are the two prong different?
For most standard two-prong plugs, there is no difference in which prong goes into which outlet. The prongs are typically the same size and shape, so it does not matter which way you plug it in. However, if the plug is polarized (one prong is wider than the other), make sure to plug it in the correct way according to the outlet.
Why wouldn't a 2 prong plug fit in a 3 prong outlet?
The reason might be a voltage or amperage mismatch between the two devices. Plugs and receptacles are matched sets depending on the voltage and the amperage of the devices. The configurations are done in this manor to prevent the wrong voltages being applied to wrong plug in equipment.
Where can I find more about dryer repair?
Repairing a dryer may be more work than it is worth but if you are intent on doing this yourself instead of calling a handyman: http://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/
What should you look for when looking at portable dryers to purchase?
First, you should look and see if it is a gas or an electric dryer. A gas dryer will save you more than an electric dryer. Then, you need to see if it is a full size or a compact dryer model.
What consumes the most money in your families home?
Your A/C or your dryer/washer , but if you leave your T.V on for >10 hours the T.V will consume more energy than your washer and dryer.
Is a gas dryer better than an electric?
Yes, a gas dryer is better than an electric dryer. A gas dryer becomes much hotter so therefore your clothes dry faster. Also natural gas as piped to homes costs less per kilowatt-hour than the equivalent amount of household electrical power. However the initial purchase cost of a gas dryer is much more than an electric dryer and the installation costs cost ofa gas dryer can be much higher too because it needs a piped gas supply as well as electricity.
What common household appliance uses more energy than NASA voyager signal?
a hair dryer
How does a t3 hair dryer differ from a regular dryer?
The t3 hair dryer is faster than other hair dryers and uses patented technology to dry hair evenly without damage. You can read more about them at http://www.t3micro.com/dryers/.
When should you purchase a new dryer rather than repair an old one?
You should buy a new one when the repair cost more then the worth of a new dryer or the worth of the old dryer itself. Also take into consideration the number of years that you have own the dryer and how reliable it will be even after repairs.
Is there any conversion plugs to go from a 4 prong 240 volt dryer outlet to a 3 pronged dryer wire?
for USA, Canada and countries running a 60 Hz supply service.Well, yes, and no. You CAN'T just disconnect the wires from the 60 amp outlet and connect them to three 20 amp outlets. It would be more like tearing out and rebuilding than converting. The 240 volt outlet has a hot wire from each side of the breaker box and each can supply a series of standard outlets if you replace the 60 amp breakers with 20 amps and pull 12 gauge wires.Actually you CAN just disconnect the wires and connect several 20 amp outlets, IF you change the breaker to a 20 amp one. The breaker/fuse has to be sized for the lowest current link, in this case it is not the wire but the outlets. The wire will be oversized but it does not need to be replaced. Some older dryer circuits also did not include a ground, so you will have to run a grounding wire or install a GFI.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Why does the Coastal Plain require more water for irrigation than other regions?
Because the Coastal Plains are dryer than the other regions
Why is static more noticeable in winter than in the summer?
For the same reason that static electricity is; colder air is dryer, and more conducive to stasis.
