0
To set the Ohm selector switch on a Marshall JMP 100 watt amplifier, you need to match the impedance settings of the amplifier with your speaker cabinet. Ensure that the Ohm selector switch on the amplifier is set to the same impedance rating as your speaker cabinet (e.g., 16 ohms for a 16-ohm cabinet). Using mismatched impedance settings can damage your amplifier and speakers. If you are not sure about the correct settings, consult the manufacturer's manual or a professional technician.
What else can I help you with?
Can you use a 250 watt bulb with a 15 amp switch?
Yes, you can use a 250 watt bulb with a 15 amp switch. The switch is rated for up to 15 amps, which is more than enough to handle the power of a 250 watt bulb. Just make sure that the wiring and other components in the circuit can also handle the load.
Can you run a 250 watt motor using a 1000 watt controller?
Yes, you can run a 250 watt motor using a 1000 watt controller as long as the voltage and current ratings are compatible. Be sure to adjust the settings on the controller to match the motor specifications to prevent damage.
What amp does alex lifeson use?
Alex Lifeson of Rush has used various amps throughout his career, including Hughes & Kettner, Marshall and Fender. One of his most famous setups included Marshall amps, particularly the Marshall 100-watt head.
Why doesn't a 1875 watt hair dryer get as hot as a 1600 watt?
A 1875-watt hair dryer may not get as hot as a 1600-watt one due to differences in design, airflow, and temperature settings. Higher wattage typically translates to more power, but if the 1875-watt dryer has a more efficient motor or greater airflow, it may prioritize drying speed over maximum temperature. Additionally, features like multiple heat settings can affect the perceived heat output. Therefore, the actual temperature reached can vary based on these factors rather than just wattage alone.
How much does a new starter switch for a Craftsman 7500 watt generator cost?
The cost of a new starter switch for a Craftsman 7500 watt generator can range from $10 to $30, depending on the brand and where you purchase it from. It is recommended to check with specific retailers or online stores for the most current pricing.
What has the author Thomas H Marshall written?
Thomas H. Marshall has written: 'James Watt 1736-1819'
What amplifiers does Adrian smith use?
He uses a Marshall DSL100 amplifier with two 300-Watt Marshall 1960A Angled-Front 4x12 Cabs and in these cabinets there are 75-Watt Celestion G12-T75 Speakers.
Can you use a Marshall MG100HDFX head to power two 1x10 cabinets from a Marshall MG15MSII Microstack setup?
I use mine to power a 4X12 Ampeg 200 Watt
Can you use a 250 watt bulb with a 15 amp switch?
Yes, you can use a 250 watt bulb with a 15 amp switch. The switch is rated for up to 15 amps, which is more than enough to handle the power of a 250 watt bulb. Just make sure that the wiring and other components in the circuit can also handle the load.
Can you run a 250 watt motor using a 1000 watt controller?
Yes, you can run a 250 watt motor using a 1000 watt controller as long as the voltage and current ratings are compatible. Be sure to adjust the settings on the controller to match the motor specifications to prevent damage.
What are five light floor lamps?
Lamps with five flexable lights that provide great lighting and come with shades and four way switches. The information below is telling you how brite the light will be if you used the same number watts in the lamp. Using 15 watt bulbs Using 30 watt bulbs Using 40 watt bulbs Using 60 watt bulb Switch 1: 30 watts Switch 1: 60 watts Switch 1: 80 watts Switch 1: 120 watts Switch 2: 45 watts Switch 2: 90 watts Switch 2: 120 watts Switch 2: 180 watts Switch 3: 75 watts Switch 3: 150 watts Switch 3: 200 watts Switch 3: 300 watts Switch 4: 0 watts Switch 4: 0 watts Switch 4: 0 watts Switch 4: 0 watts
How can I effectively control the brightness of a 1000 watt LED light using a dimmer switch?
To effectively control the brightness of a 1000 watt LED light using a dimmer switch, make sure the dimmer switch is compatible with LED lights and has a high enough wattage rating to handle the 1000 watt load. Adjust the dimmer switch to increase or decrease the voltage supplied to the LED light, which will in turn control the brightness of the light. Be cautious not to overload the dimmer switch with a wattage higher than its capacity to avoid damage.
Difference in dimmer switch heat 600 watts or 1000 watts?
A dimmer switch is used for lighting loads and not heating loads. The wattage rating on a dimmer switch is what the manufacturer recommends as the maximum load that the switch can handle. For example if you have ten 100 watt lamps, the total load wattage would be 1000 watts (10 x 100). Too much load for a 600 watt rated dimmer switch but not for a 1000 Watt rated dimmer switch. So you can see that the rating on a dimmer switch governs the maximum wattage load that can be connected in the circuit that is to be controlled.
What are the benefits of using a 1000 watt dimmer switch in a lighting system?
Using a 1000 watt dimmer switch in a lighting system allows for greater control over the brightness of the lights, which can help save energy and create different moods or atmospheres in a room.
What amp does alex lifeson use?
Alex Lifeson of Rush has used various amps throughout his career, including Hughes & Kettner, Marshall and Fender. One of his most famous setups included Marshall amps, particularly the Marshall 100-watt head.
Why doesn't a 1875 watt hair dryer get as hot as a 1600 watt?
A 1875-watt hair dryer may not get as hot as a 1600-watt one due to differences in design, airflow, and temperature settings. Higher wattage typically translates to more power, but if the 1875-watt dryer has a more efficient motor or greater airflow, it may prioritize drying speed over maximum temperature. Additionally, features like multiple heat settings can affect the perceived heat output. Therefore, the actual temperature reached can vary based on these factors rather than just wattage alone.
How much does a new starter switch for a Craftsman 7500 watt generator cost?
The cost of a new starter switch for a Craftsman 7500 watt generator can range from $10 to $30, depending on the brand and where you purchase it from. It is recommended to check with specific retailers or online stores for the most current pricing.
