answersLogoWhite

0

It sounds like the fly wheel is warped and may need to be machined to have a smooth even surface. Similar to cutting or resurfacing brake rotors or drums when brakes pulse or vibrate when applied.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

Why was there slight shudder on the evening of April 12th on the Titanic?

Because there was!


Can you give me a sentence with word shudder?

The sight of so much blood made him shudder.She shuddered at the thought of kissing him.Mention of that awful decade should make politicians shudder. Nutritionists would shudder at all the fat, sodium and trans-fats.Putting my future into the whims of the electorate makes me shudder.Bloggers often display postings that would make party censors shudder.The glider gives a slight shudder and the bottom drops out.


Will a vw beetle engine work in a bus?

The type I Beetle engine was used in the VW bus (with slight mods) from 1950 to 1971. In 1972, the bus received the new type IV engine, although certain counrties continued to use the type I Beetle motor. So yes. Check your flywheel to ensure it is the correct one.


How do you adjust parking brake on 2004 Toyota sienna?

if your van has rear drum brakes, adjust them up until there is a slight drag on the brakes. this usually does the trick to tighten up the parking brake.


In what way should the truss rod be turned to adjust the neck of a guitar?

To adjust the neck of a guitar, the truss rod should be turned clockwise to tighten and straighten the neck, or counterclockwise to loosen and create a slight bow in the neck.


What causes problem when 1991 Volvo 940 abs tries to come on at low speed only causing a shudder on pedal and a clunk noise not caliper not disc not hose?

I had this problem on my 940. It started as a slight shudder when I braked, and then there was an intermittent clunk. Then, without any warning, both of the front brakes fell off (Completely. They were dangling by their cables!). It turns out that the bolts holding the brake system on had vibrated themselves out. Try tightening the bolts and see if that helps.


How can I adjust a cycle bike properly?

To adjust a cycle bike properly, start by setting the seat height so your legs are slightly bent at the bottom of the pedal stroke. Adjust the handlebar height to a comfortable position that allows for a slight bend in your elbows. Make sure the bike is level and stable, and adjust the resistance to your desired level for a challenging workout.


How do you adjust time on cadillac DTS 2003 model?

Was it "timing"? If so- a slight adjustment to the TPS would change it a little in responce time for spark advance


What happened in 1752 to cause England less white xmases?

Eleven days removed from the calendar, to adjust for a slight miscalculation of the year's length by Julius Caesar.


What could cause a loud click click sound coming from the left rear of a 1965 VW beetle whenever it is driven it has also made a slight shake thanks -chris?

Sounds like a CV joint


What is the Difference between 73 beetle and 73 super beetle?

The Super Beetles started in '71 or '72 and and the main differences are they are a little bit longer and they went to a Strut front suspension. They also went to a curved windshield in '74 or '75. I'm not sure when the standards did. But in "general", everything behind the windshield is the same as a standard, so I'm told. But every year VW made slight changes to them both so some things will fit others and some things won't. The curved windshield on a super beetle started in '73 and had a larger plastic dashboard. Another way you can tell a beetle from a super beetle is the standard beetle's spare tire sits uprite in the front of trunk while the super lays flat on bottom of trunk.


98 Chevrolet Silverado 43 Vortec Installed a new long block assy Now will not start Acts like timing advanced too far but can't adjust timing?

Adjust the distributor and check your wires to see if installed backward. Take it to a mechanic, and they will hook it up to a programmer and adjust it using the computer and some slight turning.