answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

Why do you clean up an acid spill with a damp cloth?

OK, so how do we neutralise an acid. Answer: with a base. Because water can exist in the following state: H2O <_> H+ + OH- This means that water exists as both an acid and a base, and at pH 7, water can neutralise the base. Obviously bases of lower pH may require a basic solution to clean up, but for weak acids a watered or damp cloth will do the trick.


Can you use muriatic acid to clean green mold from a water fountain?

Yes, muriatic acid can be used to clean green mold from a water fountain, but it should be used with caution as it is a strong and potentially hazardous chemical. Make sure to follow safety guidelines, wear protective gear, and dilute the acid with water according to the manufacturer's instructions. Rinse the fountain thoroughly after cleaning to remove any remaining acid residue.


How do acid reacts with water?

You should always add (small parts of) the concentrated compound (acid, hydroxide) to (the larger amount of) water, because you can stirr and mix and cool down better (heat of hydration can be absorbed much better by the water and surroundings)


How do you clean sand colored pebble tech on the coping aarea?

A 10-20% solution of muriatic acid and bristle brush will clean the pebble tech. Be careful, the acid will burn if it comes in contact with skin or eyes. By 10% I mean 1 part acid to 9 parts cold water. Always add acid to water not water to acid due to unwanted thermal reaction.


Can you soak cuts with boric acid?

No, it is not recommended to soak cuts with boric acid. Boric acid can be toxic if ingested or absorbed in large amounts through open wounds. It is best to use safer alternatives such as clean water and mild antiseptic solutions to clean cuts and wounds.

Related Questions

What is the first thing you should do when you spill acid on your skin?

The first thing you should do when you spill acid on your skin is to immediately rinse the affected area with copious amounts of water to dilute and remove the acid. Remove any clothing that may have come into contact with the acid and seek medical attention promptly.


What do you do if an acid or alkali is spilt?

If an acid or alkali is spilled, you should immediately neutralize it by sprinkling baking soda or another neutralizing agent over the spill. Wear protective gear and use a spill kit if available. Then, clean up the spill using absorbent materials and dispose of them safely according to local regulations.


How do you clean sulphuric acid spill?

Baking soda or kitty litter will do the trick.


What do you dilute acid with if spilled on the floor?

You should dilute acid spills on the floor with a large amount of water to help neutralize the acid and reduce its corrosive effect. Make sure to wear appropriate protective gear such as gloves and goggles before attempting to clean up the spill.


What should you do if you accidentally spill sulfuric acid on your hand?

If you accidentally spill sulfuric acid on your hand, you should immediately rinse the affected area with plenty of water for at least 15 minutes and seek medical attention right away. Do not try to neutralize the acid with other substances as it can cause further harm.


How do you clean up an acid spill on a boat?

Depends what kind of acid, and what it spilled onto. - you haven't told us either one.


What to use to clean up an acid spill?

Often, massive dilution with water is enough to make it safe for ordinary clean-up. Sometimes adding a base, or a basic salt such as Sodium bicarbonate is sufficient. The nature and concentration of the spilled acid will usually dictate the clean-up method used.


How can you make an acid spill safe?

To make an acid spill safe, it is important to quickly contain the spill by using appropriate protective equipment like gloves and goggles. Neutralize the acid with a neutralizing agent, like baking soda, then carefully clean up the spill with absorbent materials. Finally, properly dispose of the waste according to regulations.


What is the best way to clean up a spill of very strong acid?

Add a lot of basic substances such as baking soda / limestone on the spill. Wait till the bubbling is complete (neutralization is complete) and then using a proper clothing, clean up the spill with a sponge.


How do you clean up spilled acid?

To clean up spilled acid, first make sure to wear appropriate protective gear such as gloves and goggles. Then neutralize the acid with a base such as baking soda or a commercial neutralizing agent. Once neutralized, carefully clean up the spill using a paper towel or absorbent material, and dispose of it according to local regulations for hazardous waste.


What would you do to some strong acid spilt onto the laboratory bench if you want to make it safe?

To safely neutralize a spill of strong acid on a laboratory bench, you should first alert others in the area and put on appropriate personal protective equipment. Use a neutralizing agent like baking soda or a commercial acid spill kit to carefully absorb and neutralize the acid. After neutralizing the spill, clean the area thoroughly with water and dispose of any contaminated materials according to proper hazardous waste disposal guidelines.


If you spill acid on your skin why should you rinse it with water?

Water removes the acid from body, but if it is sulphuric acid then do not rinse with water but first remove the acid by a dry cloth and then pour the water.