answersLogoWhite

0

The socket diameter of a bolt refers to the width of the opening in the head of the bolt for a socket or wrench to fit. It is typically determined by the size of the bolt and the type of socket needed for installation or removal. Common socket diameters for bolts range from 8mm to 24mm.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

Wheel Bolt diameter for 2007 Tacoma?

The wheel bolt diameter for a 2007 Toyota Tacoma is 12mm x 1.50.


What is diameter of lightning?

The diameter of a lightning bolt can vary widely, typically ranging from about half an inch to several inches. Lightning bolts are usually around 1 to 2 inches in diameter, but can sometimes be larger during intense storms.


Pitch of the bolt of 30 mm metric thread dia meter is?

M30 - Coarse 3.5mm, Fine 2.0mm?Metric Thread Pitch and Tapping SizesSizePitch (mm)Tapping Diameter (mm)Clearance Holes (mm)CoarseFineCoarseFineCloseMediumCoarseM1.60.351.251.71.82.0M20.41.62.22.42.6M2.50.452.052.72.93.1M30.52.53.23.43.6M40.73.34.34.54.8M50.84.25.35.55.8M61.05.06.46.67.0M81.251.06.87.08.49.010.0M101.51.258.58.710.511.012.0M121.751.2510.210.8131415M162.01.514.014.517.018.019.0M202.51.517.518.521.022.024.0M243.02.021.022.025.026.028.0M303.52.026.528.031.033.035.0M364.03.032.033.037.039.042.0


How do you fill a large hole in a wooden headboard so that a socket screw can be placed in that hole?

One way is to use a combination of washers bigger than the hole that the bolt can tighten against. You might have to get a slightly longer bolt, but all you do is take it with you to a hardware store and match it up or get a new nut and bolt that will fit through the headboard. .


What is the smallest diameter aluminum alloy bolt used in an aircraft structure?

The smallest diameter aluminum alloy bolt used in aircraft structures is typically around 1/8 inch (3.175 mm). These smaller bolts are commonly used for securing lightweight components and parts where high strength is not required.

Related Questions

What is the appropriate socket size for a 10.9 bolt?

The appropriate socket size for a 10.9 bolt is typically 17mm.


What do you mean by gross diameter of bolt?

This would be concidered the largest diameter,dimension of a bolt.


What is the standard diameter of an M3 bolt?

The standard diameter of an M3 bolt is 3 millimeters.


What is the standard diameter of an M4 bolt?

The standard diameter of an M4 bolt is 4 millimeters.


What is the nominal diameter of a bolt and how is it determined?

The nominal diameter of a bolt is the approximate size of the bolt shaft. It is determined by measuring the diameter of the threaded portion of the bolt shaft, excluding the threads. This measurement is standardized based on the bolt's size and type.


What is an Allen screw?

An Allen screw is a screw whose head has a hexagonal socket.


What does the grade 8.8 bolt identification refer to?

he diameter of the bolt.


How do you turn over an engine by hand on a 2001 Chrysler sebring convertible limited 2.7?

A ratchet and socket on the bolt that holds the crank pulley on.A ratchet and socket on the bolt that holds the crank pulley on.


What is the width of material on a bolt that is sold to public?

Bolts are sold in a variety of sizes. The measurement given is for the shaft of the bolt, not the head. So, you might have a bolt which requires a 16mm wrench or socket to turn it, but the actual measurement might be something like 16mm (diameter) x 40mm (length of the bolt shaft) x 1.5 (thread pitch).


What is the recommended installation method for a 1/4 hanger bolt in a wooden structure?

The recommended installation method for a 1/4 hanger bolt in a wooden structure is to pre-drill a hole slightly smaller than the bolt diameter, then screw the hanger bolt into the hole using a wrench or socket tool. This will ensure a secure and stable connection.


Stress on minor diameter of bolt when bolt is subjected to longitudinal force?

The stress on a bolt under longitudinal force is the total force on the bolt divided by the stress area. The stress area is a little bigger than the minor diameter area, calculated from the average of the minor diameter and pitch diameter. The total force on the bolt is its torque preload plus the (bolt stiffness/(bolt +member stiffness) x (externally applied load )


What standard size socket will fit a 5.5 metric bolt?

A 7/32 socket or wrench will fit on a 5.5mm bolt, but poorly. You risk rounding off the head of the bolt if it's stuck very tight.