answersLogoWhite

0

In house wiring it's typically a bare copper wire. It may occasionally be green.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Natural Sciences

What color wire is a grounded conductor?

Grounded conductor is white 120/240 volt & gray 480 volt. Grounding conductor is green or green with yellow.


The identified grounded circuit conductor is what color?

The identified conductor is white or natural grey in color. If you are using a zip cord (Lamp cord) is is the conductor with the ribs on it.


Where the ground wire located?

The grounded conductor is usually covered in white or light gray insulation. The grounded conductor is connected to the grounding conductor at one and only one point, usually near the transformer or in the circuit breaker panel.


What conductor should be grounded in a four wire three phase system?

The neutral conductor is typically grounded in a four-wire three-phase system to provide a path for fault currents to return to the source and to stabilize the system voltage. Grounding the neutral also helps to protect equipment and personnel from electrical hazards.


How is a 4 AWG grounded conductor in a flat multiconductor cable identified?

Although this method of identifying a grounded circuit conductor (may be a neutral) is acceptable for sizes larger than 6 AWG conductors in a raceway, it is not acceptable for multiwire cables.For sizes larger than 6 AWG installed in a raceway, this is what Item 3 of 200.6(B) allows: "At the time of installation, by a distinctive white or gray marking at its terminations. This marking shall encircle the conductor or insulation."This requirement appears in part (E) of 200.6: "Grounded Conductors of Multiwire Cables. The insulated grounded conductors of a multiconductor cable shall be identified by a continuous white or gray outer finish or by three continuous white stripes on other than green insulation along its entire length.Multiconductor flat cable 4 AWG or larger shall be permitted to employ an external ridge on the grounded conductor.

Related Questions

What color wire is a grounded conductor?

Grounded conductor is white 120/240 volt & gray 480 volt. Grounding conductor is green or green with yellow.


The identified grounded circuit conductor is what color?

The identified conductor is white or natural grey in color. If you are using a zip cord (Lamp cord) is is the conductor with the ribs on it.


What is a Grounded conductor?

The grounded conductor (Neutral) can be white or gray. The grounding conductor can be solid green, Green with a yellow tracer or bare copper.


Where the ground wire located?

The grounded conductor is usually covered in white or light gray insulation. The grounded conductor is connected to the grounding conductor at one and only one point, usually near the transformer or in the circuit breaker panel.


What is the difference between a Grounded conductor and a Grounding conductor?

In residential 120 VAC, single-phase electrical wiring, there are three main types of electrical wires: 1. Ungrounded conductor (Hot, and sometimes called "Line" or "Phase") 2. Grounded conductor (Neutral), and 3. Grounding conductor (Safety Ground or Protective Earth) The groundED conductor is the power return, intended as a current return path from the load back to the source to complete the "circuit." Its insulation is White, gray or a non-green color with white stripes. The National Electric Code requires it be connected to earth ("groundED ") at the service entrance and usually only there. The groundING conductor is usually the safety ground which serves as an emergency current return path in the event of a circuit fault or overvoltage. Like the groundED conductor, it too is grounded at the service entrance, but is also connected to metal surfaces and parts along the circuit, groundING them. It conducts current only if the current "seeks" to return to the service entrance along a path other than the Neutral (like through your chest, should a Hot wire becomes loose and contact metal in the circuit that you may touch). Since the grounding conductor doesn't normally carry current, its cross-section is sometimes smaller than the groundED conductor's. The grounding conductor's insulation is green (no other conductors can have green insulation) though sometimes it is bare copper. Sometimes the steel metal conduit enclosing the Hot and Neutral acts as the grounding conductor.


Why does copper wire have to be insulated?

To stop the conductor from touching adjacent grounded structures.


Does the grounded conductor have normal circit current flow?

Yes, the grounded conductor carries normal circuit current flow in a typical electrical system. It provides a return path for current back to the source, completing the circuit.


What color can an underground conductor not be?

an underground conductor can be any color except white, grey or green.


What happens when there is no plastic coating on a electrical wire?

Nothing happens. The wire will still conduct electricity. An example of this is the overhead utility wiring. The insulation on a conductor is there strictly to keep the conductor from touching any thing that would ground the conductor. This grounding could be from another adjacent conductor or a grounded medium around the conductor. A grounded conductor will trip the over current protection and trip the circuit off line. Without an insulation on the wire multiple wires in a conduit could not be utilized.


Can static electricity build up on an earthed conductor?

No, static electricity cannot build up on a conductor that is properly grounded (earthed). Grounding provides a path for the excess charge to flow into the earth, preventing the accumulation of static electricity on the conductor.


What is the difference between a phase to ground connection and a grounded wye connection?

A 'grounded-wye' connection describes a wye-connected supply, whose star-point (or common point) is grounded. This is essential in order to ensure stable phase voltages. I'm not sure what you mean by a 'grounded-phase' connection; if you mean a 'grounded-line' connection, then this is a short-circuit to ground from a line conductor.


What is OSHA definition of grounded?

OSHA does not provide a specific definition of "grounded." You should use the commonly accepted definition in the electrical industry. That is, a conductor that has a secure conductive path to ground, or "earth" as the term is used in the UK