answersLogoWhite

0

I'm not to sure, but i think that theres about 2 or three. Kinda vauge question but red would be positive black would be negative (sp) that's about it.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Extra wire at alternator could it be a ground wire if so where does it go?

I believe on most alt. you have a positive hot (red) wire that usually goes to the threaded bolt on the back of the alt. and goes directly to the positive terminal on the batt. and a ground wire that goes to the frame of the alt. usually you put it between the frame of the alt. and where one of the brackets bolt up to support the alt. just pinch it between the two and run the bolt through the mounting bracket and the wire and the alt. and tighten it up and that will ground it. then you will have a plug and wiring harness that just plugs into the alt.


What color is the neutral in a plug?

In the UK the neutral wire is 'blue'.


How do you change a four wire plug to a three wire plug?

I need a lot more information. I don't know what you mean by four wire plug. What does it look like, what was it used for? What three wire plug are you installing, what does it look like, what is it used for. What color ore the wires?


What colour is earth in a plug?

The color of the Earth wire in a plug is typically green or green and yellow stripes.


Voltage drops at idle on a 1998 Pontiac firebird. Battery and alternator checked good.?

there is a prob getting new rebuilt alts. you prob have the one wire set up on the pug for the exciter wire.......when you bought the replacement alt it was for a two wire set up..... still haveing the four plug set up...... im haveing the same prob w my 98 3.8 firbird......ive looked all over the net.....my next move is to get a raplacement plug harness........this will have four wires.........from what ive found the replacement alt needs 12vlts at pin b and c on the alt to make the alt start working......... crazy........ive also heard of droppping the alt off at an alt shop and haveing it converted to eliminate the exciter wire set up......


What color goes where in a 230v plug?

In a 230V plug, the standard color coding is as follows: the brown wire is the live (L) wire, the blue wire is the neutral (N) wire, and the green/yellow striped wire is the earth (E) wire. The live wire carries the current, the neutral wire returns it, and the earth wire provides a safety path in case of a fault. Always ensure proper connections and safety measures when dealing with electrical installations.


What is the color of internal amp remote wire in a 2003 dodge ram 1500?

It is pin G on the black plug to the radio, and it is the White wire.


How do you connect your PlayStation to your tv?

You have to connect the wire that has 3 separate wires at the end into your television according to the color. Plug the red wire into the red slot, yellow in the yellow and white in the white. You will then have to take the other end of the wire and plug it into the back of your playstation. Also, make sure to plug your playstation into the electrical outlet.


What does it mean if your car jumps after getting a tuneup?

Spark plug wire not connected to spark plug? Spark plug wire connected to Wrong spark plug? Vacuum line disconnected? Bad spark plug or wire?


Why would brake battery and gas warning lites stay on and ac defrost fan does not come on in an 1994 trooper alternator tested at 14 amps?

ck the plug that plugs in the back of the alt. w/ the ignition on ck for 12v at each post. it sounds like the signal wire doesnt have 12v. that wire tells the alt to turn on. did you take out and bench test it? Or did you test it in the truck?


Which wire is not present in a 2 pin plug?

In a 2-pin plug, the wire that is not present is the grounding wire. This type of plug only has two prongs for the live and neutral wires, unlike a 3-pin plug that includes a grounding wire for added safety.


How do you wire a Pollak 12-705 plug?

To wire a Pollak 12-705 plug, start by stripping the ends of the wires you’ll connect to the plug. Insert the wires into the appropriate terminals based on the color coding: typically, the brown wire connects to the tail light, the yellow wire to the left turn signal, the green wire to the right turn signal, and the white wire to the ground. Secure the wires using the screws on the terminals, ensuring a snug fit. Finally, double-check your connections with a wiring diagram to ensure accuracy before using the plug.