0
What else can I help you with?
What color should a H2 Conductor on 480 volt transformer should be marked?
The conductor for H2 connection on a 480 volt wire transformer should be marked:
What is the resistance of the secondary of a 24 volt transformer?
The resistance of the secondary of a transformer depends on the wire gauge and length of wire used in the winding. Typically, the resistance of the secondary winding of a 24 volt transformer can range from a few ohms to tens of ohms. It is best to measure the resistance using a multimeter for an accurate value.
How do you change a 220 240 volt wire to a 110 120 volt wire?
To change a wire from 220-240 volts to 110-120 volts, you will need to reconfigure the wiring by connecting it to a transformer that steps down the voltage. This transformer will reduce the voltage from the higher range to the desired lower range, allowing you to safely use it with 110-120 volt systems. It's important to ensure the transformer is compatible with the current and wattage requirements of your device or equipment.
12v transformer which of the two wires from it do you use as live?
The transformer should have identification on it. The H1 and H2 terminals are for the primary side of the transformer that connect to the supply voltage. The secondary terminals will be identified as X1 and X2 and these connect to supply the load with a voltage that it needs. This identification is regardless of whether the transformer is a step up or step down type of configuration.The primary wires would attach to the outlet, while the secondary wires would attach to your device. If there are 3 secondary wires, that means they are center tapped, most likely at half voltage, and when you use the wire that's a different color from the rest with either of the other wires, you'd have 6 volt or whatever.It is common practice in DC appliances that attach to the outlet to use two half-wave rectifier circuits to produce full-wave DC at half voltage. So a 6 volt clock radio may contain a 12-volt, center-tapped transformer, and a large stereo might contain a 24-volt, center-tapped transformer.
Can you use 240 volts with a 120 volt supply?
No, it is not possible to use 240 volts with a 120 volt supply directly. You would need a transformer to step up the voltage from 120 volts to 240 volts. Attempting to use 240 volts with a 120 volt supply without a transformer can damage equipment and pose a safety hazard.
What color should a H2 Conductor on 480 volt transformer should be marked?
The conductor for H2 connection on a 480 volt wire transformer should be marked:
What size of cable wire used for 500 kva transformer 240 volt 3 phase?
A 10 mm cable is most commonly used for a 500 KVA transformer, 240 volt, 3 phrase. The size of the wire that is used in a transformer is based on the voltage.
How do you wire a 277 to 120 volt transformer?
The voltage 277 volts is a three phase line to neutral voltage of a 480 volt system. What is needed for the protection of the transformer is a two pole breaker from the 480 volt CDP (Central Distribution Panel). The breaker will be sized to the KVA of the transformer. The wire will be sized to the breaker plus 25%. The electrical code requires that on motor and transformer feeders, they be sized to 125% of the total current capacity of the equipment.
What is the resistance of the secondary of a 24 volt transformer?
The resistance of the secondary of a transformer depends on the wire gauge and length of wire used in the winding. Typically, the resistance of the secondary winding of a 24 volt transformer can range from a few ohms to tens of ohms. It is best to measure the resistance using a multimeter for an accurate value.
Which color wire is normally hot on a 120 volt system?
black
How do you change a 220 240 volt wire to a 110 120 volt wire?
To change a wire from 220-240 volts to 110-120 volts, you will need to reconfigure the wiring by connecting it to a transformer that steps down the voltage. This transformer will reduce the voltage from the higher range to the desired lower range, allowing you to safely use it with 110-120 volt systems. It's important to ensure the transformer is compatible with the current and wattage requirements of your device or equipment.
12v transformer which of the two wires from it do you use as live?
The transformer should have identification on it. The H1 and H2 terminals are for the primary side of the transformer that connect to the supply voltage. The secondary terminals will be identified as X1 and X2 and these connect to supply the load with a voltage that it needs. This identification is regardless of whether the transformer is a step up or step down type of configuration.The primary wires would attach to the outlet, while the secondary wires would attach to your device. If there are 3 secondary wires, that means they are center tapped, most likely at half voltage, and when you use the wire that's a different color from the rest with either of the other wires, you'd have 6 volt or whatever.It is common practice in DC appliances that attach to the outlet to use two half-wave rectifier circuits to produce full-wave DC at half voltage. So a 6 volt clock radio may contain a 12-volt, center-tapped transformer, and a large stereo might contain a 24-volt, center-tapped transformer.
What color is the hot wire in a 120 volt circuit?
In the US of A, it's supposed to be black.
How do you install a tackometer?
red wire goes to 12 volt when key is on,black to ground,blue to either 12 volt key on or it really needs to tie into light switch because that is what it is for and the green wire goes to negative side of your coil
Can you use 240 volts with a 120 volt supply?
No, it is not possible to use 240 volts with a 120 volt supply directly. You would need a transformer to step up the voltage from 120 volts to 240 volts. Attempting to use 240 volts with a 120 volt supply without a transformer can damage equipment and pose a safety hazard.
What wire color is ground on a 4 wire 220 volt cord The I know the green is and what red black or white?
Depending on the configuration of the cord cap, the green wire is ground, the white wire is the neutral and red and black wires are the 220 volt source.
What color are the 12 volt wires on a Geo metros radio wire harness?
red and yellow
