answersLogoWhite

0

For starters, a four way switch must be connected to either a four way switch or a three way switch on either side. Said differently, here are some common combinations: 3way---------4way-----------3way 3way---------4way-----------4way------------3way 3way---------4way-----------4way------------4way----------------3way etc. If you are using a four way switch anywhere in a circuit both ends must have three way switches. You can use as few as one four way between the three ways, or as many as you would like. First of all, connect your white (neutral) wire straight through every box, from the power source to the light fixture being controlled. That neutral has nothing to do with the switches. On your three way switches you will see two bright screws and one dark. (Excluding the green grounding screw). One three way switch will have its dark screw connected to the power source. Two wires will run from the bright screws to the next box (the 4 way switch box). Those two wires will connect to the two bright screws on one side of the four way. The four way also has dark screws, but two of them. Connect two wires to these two dark screws, and run them to the next switch box. If the next switch box is another 4 way, repeat this again and again until you get to the last switch (a three way). Wire the last three way as follows: the two wires coming from the previous 4 way go to the bright screws. The hot wire feeding the light fixture will be the one to connect to the single dark terminal of the last 3 way switch. That's it! <><><>

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.

If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicator

to insure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How to wire a 4-way switch in a circuit?

To wire a 4-way switch in a circuit, you will need to connect the traveler wires from each 3-way switch to the 4-way switch. The common terminal on the 4-way switch should be connected to the light fixture. Make sure to follow the wiring diagram for the specific switch you are using.


How do you wire a 4-way light switch?

To wire a 4-way light switch, you will need to connect the traveler wires from each 3-way switch to the 4-way switch. The common terminal on the 4-way switch should be connected to the light fixture. Make sure to follow the wiring diagram provided with the switch for proper installation.


Can a 4 way switch be used in place of a 3 way switch?

No a 3-way is a single pole double throw. A four way switch swaps travelers.


How do you wire a 4-way switch in a circuit?

To wire a 4-way switch in a circuit, you connect the traveler wires from the 3-way switches to the 4-way switch terminals. The common terminal on the 4-way switch is connected to the light fixture. Make sure to follow the wiring diagram for proper installation.


How to wire a 4-way switch with multiple lights?

To wire a 4-way switch with multiple lights, you will need to connect the switches and lights in a specific way. Start by connecting the power source to the first switch, then connect the first switch to the second switch using 3-way switch wiring. Next, connect the second switch to the third switch using 4-way switch wiring. Finally, connect the third switch to the lights. Make sure to follow the wiring diagram for a 4-way switch setup to ensure proper functionality.


How do I properly wire a 4 way switch in a circuit?

To properly wire a 4-way switch in a circuit, you need to connect the traveler wires from each 3-way switch to the 4-way switch terminals. The common terminal on the 4-way switch should be connected to the light fixture. Make sure to follow the wiring diagram for your specific setup to ensure proper installation.


How can I properly wire a 4-way switch in my electrical circuit?

To properly wire a 4-way switch in your electrical circuit, you will need to connect the traveler wires from each 3-way switch to the 4-way switch. The common terminal on the 4-way switch should be connected to the light fixture. Make sure to follow the wiring diagram provided with the switch and turn off the power before starting the installation.


How to install a 4-way switch in a circuit?

To install a 4-way switch in a circuit, first turn off the power to the circuit at the breaker box. Remove the existing switch and identify the common wire. Connect the common wire to the common terminal on the 4-way switch. Connect the traveler wires to the remaining terminals on the 4-way switch. Install the 4-way switch in the electrical box and secure it in place. Turn the power back on and test the switch to ensure it is working properly.


How can I find a 4-way switch wiring schematic to properly install a 4-way switch in my electrical circuit?

You can find a 4-way switch wiring schematic by searching online or consulting an electrical wiring guide. This will help you understand the proper connections and installation steps for adding a 4-way switch to your electrical circuit.


Can you provide a 4 way switch diagram to help me understand how to wire a 4 way switch correctly?

A 4-way switch diagram shows how to wire a 4-way switch correctly in a circuit with multiple switches controlling a single light fixture. It involves connecting the traveler wires between the switches to control the flow of electricity. This diagram helps in understanding the correct wiring configuration for a 4-way switch setup.


Saturn Ion hazard switch?

this is the 4 way flasher switch...


How can I create a 3 way switch schematic for my home lighting system?

To create a 3-way switch schematic for your home lighting system, you will need two 3-way switches and one 4-way switch. Connect the power source to the common terminal of the first 3-way switch, then connect the travelers to the corresponding terminals on the 4-way switch. Finally, connect the travelers from the 4-way switch to the second 3-way switch. This setup will allow you to control the lighting from three different locations.