0
In North America the neutral wire is never fused. This is because of the three wire circuit that uses a common neutral. If there are two loads connected across a common neutral circuit and the neutral opens a 230 volt supply will be impressed across both loads as they are now in series with the supply. If both loads were balanced then the voltage drop across both loads would be equal. Dropping 120 volts across each load. Where the problem arises is if the two loads are not balanced and voltage drop goes higher than the manufactures recommended voltage, then the connected device could burn out.
What else can I help you with?
Why is it important that the live wire not the neutral wire is connected to the fuse?
Suppose there is a fuse which is connected to a live wire and it breaks some day because of excessive power supply. The light goes off because of that. You think that there is no power supply, but actually the neutral wire is taking current towards you. You carelessly try to repair the fuse, and you get a shock. Thus, neutral wires are not preferred in fuse.
Should neutral wire of lamp be connected to the 3amp or the 6 amp side of a canopy switch?
You should never switch the neutral wire. The neutral of the appliance should be connected directly to the neutral wire leading to the service panel neutral bar.
In plug connections does brown or blue go to the fuse connection?
In electrical plug connections, the brown wire typically connects to the fuse terminal, as it represents the live (or phase) wire. The blue wire, which is the neutral wire, should be connected to the neutral terminal. It's important to ensure proper wiring for safety and compliance with electrical standards. Always refer to local wiring regulations when making connections.
Do you connect a fuse to the live wire or the neutral wire?
A fuse is typically connected to the live wire in a circuit. This is done to protect the circuit from an overload or short circuit, as the fuse will blow or trip and cut off the current flow if there is an issue.
Why the fuse is placed in live wire only?
So that the live wire is isolated when the fuse blows. If a fuse was placed in the neutral, the equipment would still be live when the fuse blows.
Why is it important that the live wire not the neutral wire is connected to the fuse?
Suppose there is a fuse which is connected to a live wire and it breaks some day because of excessive power supply. The light goes off because of that. You think that there is no power supply, but actually the neutral wire is taking current towards you. You carelessly try to repair the fuse, and you get a shock. Thus, neutral wires are not preferred in fuse.
What happens if you incorrectly connect old black wire to new white wire?
If the wires are incorrectly connected the idea is that it will blow the fuse.
'What happens when a live electric wire falls into a river'?
The wire becomes connected to earth. In most situations this would result in a blown fuse.
Should neutral wire of lamp be connected to the 3amp or the 6 amp side of a canopy switch?
You should never switch the neutral wire. The neutral of the appliance should be connected directly to the neutral wire leading to the service panel neutral bar.
Which side of the White neutral wire do you connect the Black power wire?
The neutral wire and power wire are never connected together.
Where does the neutral wire go in fuse box?
In a fuse box, the neutral wire typically connects to the neutral bus bar, which is a metal strip or terminal that serves as a common connection point for all neutral wires from the circuit breakers. The neutral bus bar is usually grounded to ensure safety and prevent electrical shock. It is important that the neutral wire is properly connected to maintain the balance of the electrical system and to ensure the safe operation of electrical devices.
Why do white wire mark 120v?
Because the white wire on a 120 volt circuit is the neutral wire that is connected to the silver screw on outlets and switches. It is connected to the neutral bar in the service panel.
Light has to neutral wires hooked to it with hot wire nutted together one to switch one to fuse box how hook up to lights to it?
To connect the light fixture, you should connect the hot wire from the fuse box (usually black or red) to the light's hot wire (also black or red). The neutral wires (typically white) should be connected to each other, ensuring that the light's neutral wire is connected with the two neutral wires you mentioned. Finally, connect the wire from the switch to the light's hot wire, allowing the switch to control the light. Always ensure the power is turned off before making any electrical connections.
In plug connections does brown or blue go to the fuse connection?
In electrical plug connections, the brown wire typically connects to the fuse terminal, as it represents the live (or phase) wire. The blue wire, which is the neutral wire, should be connected to the neutral terminal. It's important to ensure proper wiring for safety and compliance with electrical standards. Always refer to local wiring regulations when making connections.
Do you connect a fuse to the live wire or the neutral wire?
A fuse is typically connected to the live wire in a circuit. This is done to protect the circuit from an overload or short circuit, as the fuse will blow or trip and cut off the current flow if there is an issue.
Why the fuse is placed in live wire only?
So that the live wire is isolated when the fuse blows. If a fuse was placed in the neutral, the equipment would still be live when the fuse blows.
Why fuse is not connected in neutral wire?
Because the neutral wire only carries unbalanced currents. The hot wire carries full load currents. Answer for European SystemsThe above answer is only true for three-phase systems. In single-phase systems, the neutral carries exactly the same current as the line conductor. The reason for not placing the fuse in the neutral conductor is one of safety. For example, if the fuse were to blow due to, say, an overload current, then although no current could flow, the entire conductor would remain live and highly dangerous.
