answersLogoWhite

0

Answer for USA, Canada and countries running a 60 Hertz supply service.

Voltage is the pressure that electric current (amps) is pushed by. In any given circuit, wattage (power) is what is used to run an appliance. Wattage is produced by 'pushing' a given amount of current.
However, the material in which the current is pushed (wire) can stand only so much pressure. If you use 240V on a 110V line, the wiring will no doubt burn.
If you attempt to use house current on a 240V rated appliance, you will "over-amp" the device and damage it.

<<>>

If you transpose 240V with 110V and the load is inductive it will not operate. If the load is resistive then you will only get one quarter of the rated wattage if the voltage is reduced by half.

I beg to differ with the statement," If you attempt to use house current on a 240V rated appliance, you will "over-amp" the device and damage it." There are many home appliances that utilize a 240 volt supply. The hot water tank, clothes dryer and cooking range to name a few.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you convert a 240v drill to 110v?

One word: KABOOM.


Can you rewire a 240v lamp light fitting or small appliance to 110v and if so how?

It is not recommended to rewire a 240v lamp light fitting or appliance to operate on 110v. This can be dangerous and may lead to overheating, electrical fires, or damage to the device. It is safer and more practical to use a voltage converter or purchase a new device designed to work with 110v.


Can 240v tools be converted to 110v?

No, it is not recommended to convert 240V tools to operate on 110V. The internal components of the tool are designed for specific voltage requirements, and altering them can damage the tool or pose safety risks. It is best to use tools with the voltage they are designed for.


What adapters do you need to plug your 240V Ac plug into a 110V AC supply?

There are no adptors to plug a 240v plug into a 120v receptacle. 240v requires two hot wores and a neutral and ground. 120v requires one hot wire, a neutral and a ground. If you have something that runs on 240/120 you need the cord and adaptor that came with the equipment as you willl need the wires to mate up accordingly.


Do you need a neutral when running a BLK Red and ground from a panel directly to a 240V 4800W 20A heater outlet?

No. The black is 220, the red is 220, and the ground serves as the neutral. the last answer "no" is correct but the reason is not. the ground is still a ground. the red is 110v and the black is 110v. together they are 220v. the neutral or (common) is for a 110v return. for example a stove or a dryer will have 2 hots a common and a ground because they use 220v and 110v. 220v to power the heating elements and 110 for the controls, light bulbs or the outlet on a stove. A construction heater only uses 220v and only requires the two hots and the ground for safety.

Related Questions

Can 240v coil contactor be connected to 110v supply?

no


240v box outside for a hot tub you need a 110v receptacle Can you wire it off the 240v box?

Using a box that is hire voltage than what you need can cause a short, and even a fire. So using a 240V box, when all you need is a 110v receptacle, wouldn't be a good idea.


How do you convert a 240v drill to 110v?

One word: KABOOM.


Can a 240V - 110V stepdown transformer be reversed to take a primary load of 180V to secondary 240Volts?

No


Can you rewire a 240v lamp light fitting or small appliance to 110v and if so how?

It is not recommended to rewire a 240v lamp light fitting or appliance to operate on 110v. This can be dangerous and may lead to overheating, electrical fires, or damage to the device. It is safer and more practical to use a voltage converter or purchase a new device designed to work with 110v.


Do Indian electrical devices work in US?

No India uses 240V at 50Hz the U.S. uses 110V at 60Hz.


IS there an adapter for a 240V heater that will allow you to plug it into two 110V outlets?

No. Sounds like a fairly hazardous thing to try as well. If it's to use a heater in the US, then buy a US heater at a lower cost than any adaptor that might do the job for you. If it's to use on a UK building site that has 110V but doesn't have 240V, it breaks all the rules because you end up with 240V where you shouldn't.


Can 240v tools be converted to 110v?

No, it is not recommended to convert 240V tools to operate on 110V. The internal components of the tool are designed for specific voltage requirements, and altering them can damage the tool or pose safety risks. It is best to use tools with the voltage they are designed for.


Can you run a 240v appliance ie a radio that's plugged into a socket connected to a 110v system on a market stall. h-accessories.co.UK by the way?

NO The radio will actually run at about 6 volts via an internal transformer. If you plug it into a 110v supply you will only produce 3 volts which is the same as trying to run it with flat batteries. The only way is to use a 110v to 240v transformer which will be rather large, cumbersome and heavy.


Can you plug a American laptop into England?

Check your laptops power adapter to see if it will handle both 240v(UK) and 110v(US) if it can handle 240v (which I believe most can) then all you need is a UK plug adapter.


Can you replace the 240v plug on my 240v mitre saw with a 110v plug and run it off a 110v transformer?

Changing the plug will not change the power needed to run the saw. If the saw has a dual voltage motor then a wiring change can be done to switch the saw from 240 to 110 volts. If it is not a dual voltage system then the saw must be fed with 220 volts.


Can an espresso machine with a 20A 240V Leviton plug be powered without rewiring?

You need a dedicated circuit for that. You cannot power a 220V device off 110V.