answersLogoWhite

0

This is what the purpose of a switch is. It connects the "hot" wire to the load. When this is done the load becomes energized.

User Avatar

Wiki User

10y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you connect a main switch?

The line supply connects to the top terminals of the switch and the load connects to the bottom terminals of the switch.


How do you wire dual switch-plug gfci which has extra wires?

To wire a dual switch-plug GFCI with extra wires, you need to identify the line and load wires. The line wires bring power to the GFCI, while the load wires carry power to additional outlets or devices. Connect the line wires to the line terminals on the GFCI and the load wires to the load terminals. Make sure to follow the wiring diagram provided with the GFCI and use wire connectors to secure the connections.


Were do you connect the dimmer wire?

There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M. There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M.


The line side of a switch is the?

The line side is where the source of the voltage is connected. The load side is where the device being switched is attached. In the case of a light switch the line side would connect to the house power and the load side would be the bulb. The switch is usually inserted in the line carrying the load (or black wires). As it it common to use 12-2 wiring to run from the device being switched to a switch on the wall, the return wire can be colored white. A electrician places an identification on the wire to signal that it is a "hot wire" even though it is white. Typically the electrician will wrap the white wire with black tape for about 1 inch to indicate this. A white wire is normally considered to be neutral if it is not identified as a "hot or load wire".


How do you wire a switch outlet combo circuit to an existing 3 way light switch?

A switch is just a break in your hot wire. Your incoming power is usually on the bottom of the switch. Hook that one up to the hot side(gold in color) of the receptical and either pull the other wire out or snip the end off that is exposed and put a wire nut on it. Now you have to have a neutral wire(white). If there's one in there that was not hooked to the top of the switch then hook it to the silver screw of the recep. If one is not in there you'll have to bring one to it and you'll be good to go.

Related Questions

How do you connect a main switch?

The line supply connects to the top terminals of the switch and the load connects to the bottom terminals of the switch.


How do you install an on off switch from an existing wire?

If you are asking how to add a switch to a lamp (or other load device) cord, simply cut the line side of the cord and connect to the switch terminals. ----mikey


How do you UNCHARGE a capacitor?

Connect it, in series, to a resistor or a dummy load and a switch. And then throw the switch.


How do you wire a 2-way switch in a circuit?

To wire a 2-way switch in a circuit, connect the power source to the common terminal of the first switch. Then, connect the travelers from the first switch to the corresponding terminals on the second switch. Finally, connect the load to the common terminal of the second switch. This setup allows you to control the load from either switch.


How do you properly wire a 2 way switch in a circuit?

To properly wire a 2-way switch in a circuit, connect the power source to the common terminal of the first switch. Then, connect the travelers from the first switch to the corresponding terminals on the second switch. Finally, connect the load to the common terminal of the second switch. This setup allows you to control the load from either switch in the circuit.


How do you wire a disconnect box?

To wire a disconnect box, first turn off the power supply. Connect the wires from the power source to the line side of the disconnect switch. Then, connect the wires from the load to the load side of the switch. Make sure to follow the manufacturer's instructions and local electrical codes for proper installation.


How do I correctly connect the red and black wires to a light switch?

To correctly connect the red and black wires to a light switch, first turn off the power to the circuit. Connect the black wire to the screw terminal labeled "hot" or "line" on the switch. Connect the red wire to the screw terminal labeled "load" or "out." Make sure the connections are secure and then turn the power back on to test the switch.


How should I properly wire a GFCI outlet with a switch?

To properly wire a GFCI outlet with a switch, connect the incoming power supply to the line terminals on the GFCI outlet. Then, connect the switch to the load terminals on the GFCI outlet. Make sure to follow the manufacturer's instructions and consult a professional if needed.


How should I properly wire a GFCI switch in my electrical circuit?

To properly wire a GFCI switch in your electrical circuit, follow these steps: Turn off the power to the circuit at the breaker box. Connect the incoming power supply wires to the LINE terminals on the GFCI switch. Connect the outgoing load wires to the LOAD terminals on the GFCI switch. Connect the ground wire to the grounding terminal on the GFCI switch. Securely mount the GFCI switch in the electrical box. Turn the power back on and test the GFCI switch to ensure it is working properly.


What is the difference between a line and load in a light switch circuit?

In a light switch circuit, the line is the wire that brings power into the switch, while the load is the wire that carries power from the switch to the light fixture. The line wire is typically connected to the power source, while the load wire is connected to the light fixture.


How do you wire dual switch-plug gfci which has extra wires?

To wire a dual switch-plug GFCI with extra wires, you need to identify the line and load wires. The line wires bring power to the GFCI, while the load wires carry power to additional outlets or devices. Connect the line wires to the line terminals on the GFCI and the load wires to the load terminals. Make sure to follow the wiring diagram provided with the GFCI and use wire connectors to secure the connections.


Will a circuit work with the switch and will it work if you take the switch out of the circuit?

A switch is used to connect or disconnect a load from a source of voltage. If you take the input and connect directly to the output the result is that the connected device is always on.