0
What else can I help you with?
If an evaporator has a pressure drop of10psig and the low side pressure is 15psig what is the pressure at the inlet of the evaporator?
To find the pressure at the inlet of the evaporator, you subtract the pressure drop from the low side pressure. Given a low side pressure of 15 psig and a pressure drop of 10 psig, the inlet pressure would be 15 psig - 10 psig = 5 psig. Therefore, the pressure at the inlet of the evaporator is 5 psig.
How do you convert psig tp psia?
PSIG refers to pound/force per square inch gauge, while PSI measures the pressure relative to a vacuum. If you want to convert a figure from PSIG to PSI, you would need to add 14.7psi to your PSIG figure, which will give you your PSIA result.
When leak testing a low pressure centrifugal with nitrogen what is the maximum test pressure?
10 psig
What is the saturation temperature of r-410a at 38 psig?
The saturation temperature of R-410A at 38 psig is approximately 18.5°C or 65.3°F.
How much psig equal to 1 psi?
There is no mathematical conversion needed - 1 psi is equal to 1 psi. The terms "psig" and "psi" are often used interchangeably to refer to pounds per square inch of pressure. However, "psig" specifically denotes pressure relative to the local atmospheric pressure, while "psi" is an absolute measure.
How do you convert 15 psia to psig?
psia to psig psig - 15 15 - 15= 0 psig
100 psia to psig?
psia=psig+atmospheric pressure where, atmospheric pressure = 14.7psi therefore psig=psia-atmospheric pressure psig=100-14.7 psig=85.3psig
What is blow down pressure of safety valve?
the blowback or blowdown of the safety valve is at least 2 psi and for pressures over 100 psig is 2% of the popping pressure. The blowback is adjusted with the adjusting ring on the safety valve. The blowback is the pressure less than the popping pressure at which the safety valve will reset. Examples: a safety valve set to pop at 15 psig will reseat at 13 psig, the blowback is 2 psi. A safety valve set to pop at 250 psig will reseat at 245 psig the blowback is 5 psi or 2%.
What does 85 psia equals in psig?
70 psig
7 inches water column equal how many PSI?
1 psig is equivalent to 51.71 mm (2 in) of mercury or to approx 700 mm (27.5 in) of water. Technically one cannot have apsig. Psig represents a pressure reading of the pressure above normal atmospheric pressure of 14.7 psi. You mean a psi.
What is the pressure rating for xxh pipe nipples?
You asked for black iron pipe ratings but below is an explanation for CARBON steel, which is much stronger. Iron and steel are not the same thing. The working pressure depends on the size of the pipe. These pressures are rated up to 400 degrees F. THESE RATINGS ARE FOR *CARBON STEEL*NOT BLACK IRON! Again, these pressures are maximum working pressures, not burst pressures. 1/4" 188psig 3/8" 203 psig 1/2" 214 psig 3/4" 217 psig 1" 226 psig 1-1/4" 229 psig 1-1/2" 231 psig 2" 230 psig The full table can be found here: http://www.engineeringtoolbox.com/astm-steel-pipes-working-pressure-d_775.html
What term is more commonly use in refrigeration psia or psig?
psig
What is the fuel pressure on a 1973 beetle carburated engine?
should be 2 to 3 psig
What is 0.5 psig in inches of water column?
0.5 psig is equivalent to 13.8 inches of water column.
How do you convert 55 psig to absolute pressure?
55 psig +15=70
What is 50 psig in psi?
50 psig is equivalent to 64.7 psi. To convert psig to psi, you simply add the atmospheric pressure at sea level, which is about 14.7 psi.
If an evaporator has a pressure drop of10psig and the low side pressure is 15psig what is the pressure at the inlet of the evaporator?
To find the pressure at the inlet of the evaporator, you subtract the pressure drop from the low side pressure. Given a low side pressure of 15 psig and a pressure drop of 10 psig, the inlet pressure would be 15 psig - 10 psig = 5 psig. Therefore, the pressure at the inlet of the evaporator is 5 psig.
