0
The torque of a 3 hp (horsepower) electrical motor operating at 1440 RPM (revolutions per minute) can be calculated using the formula: Torque (in lb-ft) = (HP × 5252) / RPM. For a 3 hp motor at 1440 RPM, the torque would be approximately 10.87 lb-ft. This value may vary slightly based on motor efficiency and design specifics.
What else can I help you with?
What is the number of plugs can a 15 amp circuit handle?
A 15 amp circuit can handle approximately 1440 watts of power. To determine the number of plugs it can handle, divide the total wattage of the devices plugged in by 1440 to ensure that the circuit is not overloaded.
12 amp vacuum that is 120 volts how many watts is that?
To calculate the watts, you can use the formula: Watts = Voltage x Amperage. In this case, it would be 120 volts x 12 amps = 1440 watts. Therefore, the 12-amp vacuum cleaner operating at 120 volts uses 1440 watts of power.
How many inches in 120 feet?
1440 inches
1440 ml is how many liters?
1440 ml is equal to 1.44 liters. To convert milliliters to liters, you divide by 1000 because there are 1000 milliliters in a liter.
How many ounces is 90 pounds?
16 ounces equals one pound so to figure out how many ounces are in 90 pounds so use the following equation: 90 pounds X 16 ounces = 1440 ounces 1440 ounces equal 90 pounds.
How much torque does a 425 caterpillar engine have?
520-860 lb-ft @ 1440 rpm
What is 1 percent of 1440 minutes?
1% of 1440 = 1% * 1440 = 0.01 * 1440 = 14.4
Is 1440 composite or prime?
1440 is not a prime number; 1440 is composite.
What are the first 5 common multiples of 36 32 and 45 and 10?
LCM(36, 32, 45, 10) = 1440 so the answer is 1440, 1440*2, 1440*3, 1440*4 and 1440*5.
What is the least common multiple of 5 and 1440?
The LCM of 5 and 1440 is 1440
How do you calculate maximum current of 3 phase motor?
By using a simple formulae: f=np/60 where f= frequency, n is the number of pair of poles and 60 is in seconds that motor is turning. So a 4 pole motor with a frequency of 50 hertz will run at 1500 rpm. By manupilating the formulae: n= 50 multiplied by 60 devided by 2 therefore n= 1500rpm. The formula 120xFrequency/poles gives synchronous speed not actual shaft RPM. Induction motors must run at a certain % slip to obtain torque, so a 4 pole motor running at 50hz would be 120x50/4 = 1500 rpm, at 4% slip (operating speed) actual shaft RPM or rated speed would be 1440 RPM.
What is 25 percent of 1440?
25% of 1,440= 25% * 1440= 0.25 * 1440= 360
What is the next number in this pattern 12 24 72 288?
It is: 1440
WHAT IS 4800-1440?
4800-1440 = 3360
What is 1440 simplifed?
1440 is already simplified.
what is 1440 divided by 120?
1440 divided by 120 = 12
Is 4 divisible by 1440?
No. 4 is less than 1440 so it cannot be divisible by 1440. Unless we use decimals, in which case 4/1440 = 0.0027778.
