answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

What is the largest wire allowed to wrap around a grounding screw?

In whole, wiring of most circuits are fed with a #14 wire cable rated at 15 amp circuits. In this case a #14 ground wire would be used.There are some individual cases where a #10 cable set uses a # 10 solid ground wire. This size conductor can be formed into an eyelet and fastened to the device with a screw and washer.Any ground wires larger that # 10 must be terminated into a wire end lug. This lug can be of the set screw or compression variety. The lug is then connected to the device with a screw which then grounds the device to the electrical distribution's ground bus at the panel board end.


When assembling a loadbreak elbow what kind of abrasive cloth is used to prep the insulation and compression lug before the cable is pushed into the elbow?

Silicon carbide abrasive cloth is commonly used to prep the insulation and compression lug before inserting the cable into a loadbreak elbow. It helps to ensure a clean surface for proper electrical connections and reduces the risk of contamination during the installation process.


Where do you purchase a bonding strap for a dryer?

You can purchase a bonding strap for a dryer at hardware stores, home improvement stores, or online retailers that sell electrical supplies. It is important to have a bonding strap installed to ensure proper grounding and safety for your dryer.


Can you tie the neutral wire on a sub feed to another panel to the main neutral lug?

No, the neutral wires from different panels should not be tied together at the main neutral lug. Each panel should have its own separate neutral connection to the main service panel to ensure proper grounding and to prevent potential hazards such as ground faults. Mixing neutral wiring from different panels can cause electrical imbalances and safety issues.


What section of the nec covers grounding?

Article 250 of the National Electrical Code covers grounding.

Related Questions

What is the difference between earthing boss and earthing lug and where to use?

An earthing boss and earthing lug are parts of a grounding connection. An earthing boss is in a casting that allows for the drilling and tapping of hole. A earthing lug is used to bond a wire to the ground.


How many crimps should you place on the compression lug when assebling a loadbreak elbow?

as many as will fit without overlapping


What is the largest wire allowed to wrap around a grounding screw?

In whole, wiring of most circuits are fed with a #14 wire cable rated at 15 amp circuits. In this case a #14 ground wire would be used.There are some individual cases where a #10 cable set uses a # 10 solid ground wire. This size conductor can be formed into an eyelet and fastened to the device with a screw and washer.Any ground wires larger that # 10 must be terminated into a wire end lug. This lug can be of the set screw or compression variety. The lug is then connected to the device with a screw which then grounds the device to the electrical distribution's ground bus at the panel board end.


When assembling a loadbreak elbow what kind of abrasive cloth is used to prep the insulation and compression lug before the cable is pushed into the elbow?

Silicon carbide abrasive cloth is commonly used to prep the insulation and compression lug before inserting the cable into a loadbreak elbow. It helps to ensure a clean surface for proper electrical connections and reduces the risk of contamination during the installation process.


Is this how you spell grounding?

The correct spelling is grounding.


Can 5 lug rims fit on a 4 lug car?

5 lug rims will not fit on a 4 lug car.


Can 6 lug rims fit a 5 lug vehicle?

no six lug wheels will not fit five lug vehicles


What is a starjack?

I think you're talking about a grounding connector that allows multiple connections to be made to it, thus looking like a 'Star' when viewed from above. This would be opposed to a single-connection 'jack' where only one connection is made to the 'jack', or lug.


Where do you purchase a bonding strap for a dryer?

You can purchase a bonding strap for a dryer at hardware stores, home improvement stores, or online retailers that sell electrical supplies. It is important to have a bonding strap installed to ensure proper grounding and safety for your dryer.


Is a 6 lug ford 4x4 the same lug pattern as a 6 lug Chevrolet?

NO


Do 5 lug universals fit 6 lug?

No they are only universal on 5 lug


Can a 5 lug rim be welded into a 6 lug rim?

I think you mean wheels but no a 5 lug can not be converted onto a 6 lug