Indirect hot water refers to a system where hot water is produced by a separate device, such as a boiler or water heater, and then circulated through a heat exchanger in a tank to heat the water stored there. This method of heating water is often more efficient and can provide a continuous supply of hot water.
Tepid is lukewarm water so obviously hot water!
hot water is hotter cause hot water is always hot
Hot Water Is Hotter Than Tepid Water Because Tepid water is at body temperature, so should not feel either hot or cold when it touches your skin.hot water
A hot water bottle is also known as a hot water bag or a warming bottle.
hot water
Indirect Hot Water System.
At the lowest point on the hot water distributing pipework system
== == It is accomplished by adding an indirect fired water heater and controls.
Conduction
Direct hot water cylinders are heated directly by an immersion heater within the cylinder, whereas indirect hot water cylinders are heated indirectly by a boiler or other external heat source through a coil or heat exchanger within the cylinder. Indirect cylinders are more efficient as they can be connected to renewable energy sources like solar panels or heat pumps.
Techtanium is a brand of indirect water heater. It heats water for things like showers/baths, dishes, and anything else that requires hot water.
There are four main types of hot water cylinders: Direct hot water cylinders. These cylinders have an immersion heater inside that heats the water directly. They are the most basic type of hot water cylinder, and they are relatively inexpensive. However, they can be inefficient, and they can take a long time to heat up the water. Indirect hot water cylinders. These cylinders use a heat exchanger to heat the water. The heat exchanger is connected to a boiler, which heats the water from the mains supply. Indirect hot water cylinders are more efficient than direct hot water cylinders, and they can heat up the water more quickly. However, they are also more expensive. Vented hot water cylinders. These cylinders are connected to a cold water tank. The cold water tank is located above the cylinder, and it provides the water that is used to heat the water in the cylinder. Vented hot water cylinders are the most common type of hot water cylinder in the UK. They are relatively inexpensive, and they are easy to install. However, they can be inefficient, and they can lose heat through the venting system. Unvented hot water cylinders. These cylinders are not connected to a cold water tank. Instead, they are connected directly to the mains water supply. Unvented hot water cylinders are more efficient than vented hot water cylinders, and they do not lose heat through the venting system. However, they are also more expensive, and they require a special type of expansion vessel. The type of hot water cylinder that is right for you will depend on your individual needs and requirements. If you are looking for an inexpensive option, then a direct hot water cylinder may be a good choice. If you are looking for an efficient option, then an indirect hot water cylinder may be a better choice. If you are concerned about losing heat, then an unvented hot water cylinder may be the best option for you.
Single feed indirect cylinder
A single feed indirect cylinder is a type of hot water cylinder that is indirectly heated by a boiler or another heat source. It has a single inlet for the heated water, which circulates through a coil or heat exchanger inside the cylinder to transfer heat to the stored water. This design helps prevent contamination of the drinking water supply.
Answer:An indirect water heater uses the home heating system (furnace/boiler) to supply domestic hot water on demand- without a tank. It does this by use of a separate or secondary coil or heat exchanger which is piped to the domestic water system installed in the home heating source in your home. Hence, the name Indirect.
It would depend on how the water was heated. Tankless Coil, there should be a valve on the side of the coil, that has a knob on top, that is your mixing valve and should be used to adjust water temp. Indirect Hot Water Tank, it is connected to boiler through piping, but does not have it's own burner...should have a box on it, (aquastat), that will adjust the temp of your hot water, likewise with a Direct Fired Hot Water Tank, which is the same as mentioned above, but with it's own oil burner.
In the sentence The soapy water felt very hot there is no object, either direct or indirect. (Obviously, there are some unconventional grammars such as Charles Fillmore's case grammar, where The soapy water might at a pinch be interpreted as a semantic object, but I can't imagine that is what your teacher wants).