0
What else can I help you with?
Can you use a double 30amp breaker to feed 2 15 amp?
no, load will brake at 30 not 15 as needed
Which terminal on a 15 amp household breaker does the hot wire feed into and which one does it come out?
On a 15 amp household breaker there is no terminal on the in feed of the breaker. The breaker either plugs into the distribution panel's bus bar or it bolts to the distribution's bus bars. The feed conductor connects to the load side of the breaker at its terminal lug.
What size circuit breaker should be used on 125 feet of 4 AWG power feed?
The circuit breaker is used to protect the conductor that is connected to it from an overload condition. On a motor load the breaker has to be sized 250% of the motors full load amperage. Some circuits can be only loaded to 80% capacity and this is governed by the sizing of the breaker. Without knowing what the load amperage is, this question can not be answered.
What are the four major load control functions found on a lift?
The four major load control functions found on a lift are load sensing, load holding, load monitoring, and overload protection. Load sensing ensures the lift adjusts its operation based on the weight being carried, load holding prevents the lift from moving when under load, load monitoring provides feedback on the load status, and overload protection stops the lift from operating if the load exceeds its capacity.
What the four major load control functions?
The four major load control functions are load forecasting, load scheduling, load dispatching, and load balancing. Load forecasting involves predicting future electricity demand based on historical data and trends. Load scheduling allocates resources to meet the forecasted demand, while load dispatching ensures the optimal generation units are activated to supply the required load. Finally, load balancing maintains the equilibrium between supply and demand in real-time to ensure system stability.
What could you try if your horse does not load?
When my horse does not load i try bribing him with oats or complete feed.
You have three phase electric load of 29.3Kw what is thesuitable cable to feed this load if the distance between the supply and load is 270metres?
yes
How do you tell which is the line wire and the load wire?
The line wire will be hot and carrying power when the breaker is on. The load wire will not be hot and will have no voltage on it until it is connected with the line wire.
Can you use a double 30amp breaker to feed 2 15 amp?
no, load will brake at 30 not 15 as needed
What are breakers?
A breaker is a device that is used to connect and disconnect the buss bars of an electrical panel to the feed end of wires that feed an electrical load. The function of a breaker is to protect the wires from an overload by the use of an internal thermal trip, and to protect the load and wires from a short circuit by use of an internal magnetic trip.
How do you make the voltage high to avoid voltage drop?
The problem of over coming voltage drop is not to raise the voltage but lessen the resistance of the feed conductor. This is done by increasing the circular mil capacity of the conductor. In other words increase the size of the feed conductor allowing the load to receive its proper operating amperage at its proper operating voltage. Average allowable voltage drop on a load feed conductor is usually 3 percent of the load's nameplate rating.
What is meant by the term load centre?
A load center, or distribution board, is a panel that distributes electrical power in a building. It typically contains circuit breakers or fuses to protect circuits from overloading. The load center is where the main power feed enters a building and branches out to various circuits.
What do kingfish feed on?
well...... human lollies i really actually dont no im just writing a hole load of lies #dontnothisshit
How do you load paper in an SPL-P500 calculator?
Just jam the paper in there holding the feed button until it starts feeding through!
What feed is good?
totally depends on the horses current health status, the work load, environment you should find out information like this about the horse then look at certain brands, or ask around as to what other people around you feed
What you will do if both feed pumps tripped when boiler is in service?
Immediately the load on Generator should be reduced to Zero n desynchronised, and the turbine be tripped.
How do you load a Glenfield Model 60?
Unscrew the magazine tube (located near the muzzle of the gun) and pull it out until the ammunition feed port (located on the bottom of the magazine tube) is open. Feed the ammunition in primer first and drop down the tube. Once loaded, push the tube back down and screw to secure. Cycle the action to load the ammo. Be careful and have fun.
