answersLogoWhite

0

Phosphoric acid based products will directly react with calcium and rust stains. Something like Edfred products unless it is a slate or marble shower, then caution is advised.

toothpaste v/salts using a scotch brite pad....rinse with water vinegar solution....

best cleaner ever for these type of surfaces....

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Natural Sciences

To make your own shower stall do you need to have your drain lower?

The drain has to be slightly lower than the rest of the floor. If you tile over a cement floor, it will very gently slope down to a central drain, or a drain at the end. Try to visit some that have been done the way you want to help envision this.


How to Install Mortar Shower Pan Membrane Liner?

How to Install Mortar Shower Pan Membrane LinerOnce you've framed the shower stall, it is time to install the pan liner and cement backer board to create a water tight seal.Remove the drain cap and tape over the drain to keep mortar and other debris from entering the drain. Put down a layer of felt paper to help prevent moisture from wicking down through to the subfloor. Place a layer of metal lathe over the felt paper. Trowel in a layer of mortar that it has a one quarter inch slope towards the drain. Once the mortar dries, place a layer of felt paper along the walls of the shower stall. Attach cement board with the rough side out along the top half of the walls. Install the shower stall membrane in the bottom of the shower so that it overlaps in the corners, covers the shower curb and is approximately six inches up the side of the walls. Cut out holes for the drain, the drain bolts and the weep holes. Seal the underside of the membrane near the drain with silicone. Nail the membrane that covers the curb only on the outside. Attach the remaining cement board leaving one inch clearance from the bottom. Caulk all seems. Place some pebbles near the weep holes to protect the openings. Trowel in a layer of mortar that has a one quarter inch slope towards the drain. Mortar the curb. Remove the tape from the drain.


How far must an electrical switch be from a bathtub to be safe?

Answer for USA, Canada and countries running a 60 Hz supply service.The simple answer for the USA, Canada and countries using similar 120 Volt, 60 Hz mains power supply systems, is " 36 inches" or "about one hundred centimetres".Always be sure to switch off the breakers at the main panelbefore you attempt to do any workon any mains power circuit.In countries using 230 Volt, 50 Hz servicestotally different wiring regulationscover the types of switches and sockets which are allowed in wet placessuch as bathrooms, kitchens, etc.Answer for countries in Europe and other world areas running a 50 Hz supply service.A plate light switch must be at least 0.6m from the edge of the bath or shower and be suitable for the location (IP rated).A pull-cord switch is the type that should be installed!No socket outlet must be installed within 3 meters from the edge of the bath or shower basin, so you would need a big shower room to put one in!!Remember, any circuit installed in a bathroom or shower room (other locations apply) MUST be RCD protected! As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


Can condensation in your gas cause it to stall out?

Yes, condensation in your gas can lead to stalling. The water from the condensation can mix with the fuel and disrupt the combustion process in the engine, causing it to stall. It is important to regularly drain any water or condensation from your gas tank to prevent this issue.


When you take a showers and there is lighting what happens?

When lightning strikes, the electricity can travel through plumbing and pipes, potentially reaching someone showering or using water. This can lead to electric shock, although the chances are low. It's recommended to avoid using electrical appliances during a thunderstorm to reduce the risk.

Related Questions

How do you eliminate stains in a shower stall?

Most shower stains are either mildew or soap scum (which is a combination of product and lime build up). If I start getting stains in the shower, I use comet to scrub the tub down. Let it sit for a while, and then rinse it out very thoroughly. When you are finished, if the stains are still there, try Lime-A-Way. It also works on your shower head! Black stains on tile are typically caused by mildew, an air-borne fungus that thrives in humid locations. Use a weak concentration of chlorine bleach in a spray bottle, but make sure the shower gets plenty of air when you do that, the chlorine can cause you somee problems if it gets too strong. Use 5% to 10% chlorine bleach in water and spray it directly on the mildew. If it dries out too quickly, you may need to use some tissue to keep it wet longer. Spray the mixture on the tissue and bunch up the wet tissue over the stains. If the stains are white, brown or green or basically any color except black, it might be mineral stains and you'll need to use something like CLR to get the stuff off.


How much does a corner shower stall cost?

The costs will vary according to the quality of the corner shower stall. However a medium quality corner shower stall would be about $6000 to buy and install.


Do you have to put backer board behind the tub below the shower stall area?

No you not have to put backer board behind the tub below the shower stall area. You only need to use it behind the walls of the shower stall.


How tall is a typical stall shower door?

A typical shower door is 72".


Can shower head be installed above shower stall?

You can put it at any height. Unless there is some other reason not to, something structural, I always put them above the shower stall for taller people.


An architect has submitted plans for a shower stall. The client wants to know if the shower stall is shaped like an isosceles trapezoid. Which statement is true?

WXYZ is a trapezoid......


What are the benefits of using a curved shower rod for a shower stall?

A curved shower rod can provide more space inside the shower stall, making it feel larger and more comfortable. It also helps to prevent the shower curtain from sticking to your body while showering, reducing the risk of water splashing outside the stall. Additionally, the curved design can add a stylish and modern touch to the bathroom.


What are some important considerations to keep in mind when selecting a mobile home shower stall?

When selecting a mobile home shower stall, important considerations include the size and layout of the bathroom, the material and durability of the shower stall, the ease of installation, and the overall aesthetic appeal to match the style of the mobile home.


How can I install a shower stall?

To install a shower stall, first measure the space and choose a stall that fits. Next, prepare the area by removing any existing fixtures and ensuring the plumbing is in place. Install the shower pan, walls, and door according to the manufacturer's instructions. Seal the seams and connections to prevent leaks. Finally, test the shower for proper drainage and functionality.


What is a 4 piece bathroom?

it has a toilet, sink, shower and tub. (if it has a shower stall and no tub it is called a 3 piece)


cleaning my shower stall?

There are many products you'll find to clean your shower stall at the grocery store. Once you have it all removed, a great mold preventative is to spray some vinegar water in your shower stall after each use. Also be sure to use your bathroom fan, and to keep it running long after you've finished bathing.


What is the best type of shower stall curtain rod to use for a small bathroom with limited space?

A tension rod is the best type of shower stall curtain rod to use for a small bathroom with limited space. It can be easily adjusted to fit the size of the shower stall and does not require drilling into the walls, making it a convenient and space-saving option.