answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

How is the load determined for outlets supplying specific appliances?

The load for outlets supplying specific appliances is determined by calculating the power requirements of the appliance (in watts or amps) and ensuring that the outlet and electrical circuit can safely handle that demand. This involves considering factors such as voltage, current, and the anticipated usage of the appliance to prevent overloading the circuit. It's important to refer to the appliance's manual or consult an electrician to determine the correct load for each outlet.


What number wire gauge for a single pole light switch?

In residential wiring applications the most used is 14 gauge wire for light switches as long as the circuit breaker or the fuse is 15A. If your lighting circuit is on a 20A fuse/circuit breaker then you need to use 12 gauge wire


How do you add lighting to an unfinished basement?

=== === By asking this question you are probably not quite ready to take on this particular task. The correct answer to your question will depend on the distance from the breaker panel and exact locations of the lighting units, their voltage and power rating. Additional lighting and wiring for it can be pulled off an existing lighting circuit as long as the circuit breaker for the circuit still has unused current capacity available AND the existing wiring is capable of carrying the extra current load without overheating or catching fire. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


What is the requirement for energizing a 120 volt circuit breaker?

Before energizing a breaker for a circuit, the circuit has to be clear of any short circuits or grounds. This can be accomplished by the use of a megger on the correct voltage setting.


Why do your fuses keep tripping?

A fuse trips when the current in the circuit is too high. You either have a failing component, a shorted wire, or too many components in the circuit.Well, my fuses don't keep tripping. But apparently yours are, so here goes: first of all, fuses don't "trip", their elements burn or melt due to more current or amps passing through them than the fuse is rated for.Circuit breakers "trip" for the same reason but can be reset whereas fuses can't be reset but must be replaced.There are numerous reasons why your fuses keep burning out. Understand that the fuse is there to protect the wiring and the device the fuse is supplying power to.The most common reasons are:1. the fuse is too "small", that is, its amp rating is too low for the load. However, do not install a higher amp rated fuse into the circuit unless you are absolutely sure of the correct circuit amperage rating. Otherwise you may burn up the wiring on the load side of the fuse or damage the device it is supplying power to. If the fuse was factory installed, then it should be the correct amperage rating.2. assuming the fuse is the correct size (amp rating) then the load it is supplying power to is drawing too much current and is defective, and should be replaced. What is the load the fuse is supplying power to? If you post a more definitive question, someone may be able to give you more information.

Related Questions

How do you spell supplying?

That is the correct spelling of "supplies."


How can password protected floppy disks be accessed?

By supplying the correct password.


Which is correct in connection to or in connection with?

Either is correct, although in some contexts one may be more common than the other.


How is the load determined for outlets supplying specific appliances?

The load for outlets supplying specific appliances is determined by calculating the power requirements of the appliance (in watts or amps) and ensuring that the outlet and electrical circuit can safely handle that demand. This involves considering factors such as voltage, current, and the anticipated usage of the appliance to prevent overloading the circuit. It's important to refer to the appliance's manual or consult an electrician to determine the correct load for each outlet.


When electric current is flowing in a circuit if the voltage applied to the circuit is increased the?

Correct Answer= "the current will increase"


What is the correct way to connect the ground and hot wires in an electrical circuit?

The correct way to connect the ground and hot wires in an electrical circuit is to connect the hot wire (usually black or red) to the brass-colored screw terminal and the ground wire (usually green or bare copper) to the green screw terminal on an electrical outlet or switch. This ensures proper and safe electrical connection.


How do you spell asotiation?

The correct spelling is "association" (connection, or a group).


What number wire gauge for a single pole light switch?

In residential wiring applications the most used is 14 gauge wire for light switches as long as the circuit breaker or the fuse is 15A. If your lighting circuit is on a 20A fuse/circuit breaker then you need to use 12 gauge wire


How do you add lighting to an unfinished basement?

=== === By asking this question you are probably not quite ready to take on this particular task. The correct answer to your question will depend on the distance from the breaker panel and exact locations of the lighting units, their voltage and power rating. Additional lighting and wiring for it can be pulled off an existing lighting circuit as long as the circuit breaker for the circuit still has unused current capacity available AND the existing wiring is capable of carrying the extra current load without overheating or catching fire. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


What is the correct for a protective device for a 9kW shower circuit?

15A


Is Related with correct?

No, the correct phrase is "related to" when indicating a connection or association between two things.


How do you spell realastionship?

The correct spelling is relationship (a peer or family connection).