answersLogoWhite

0

To store gas.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Natural Sciences

How do you control the height of the flame on a bunsen burner?

The height of the flame on a Bunsen burner can be controlled by adjusting the gas supply using the gas tap. Turning the gas tap to increase the gas flow will raise the flame height, while decreasing the gas flow will lower the flame. Positioning the collar on the burner can also help control the air-to-gas ratio and influence the flame height.


Turning off the Bunsen burner at the gas tap puts out the fire because?

Turning off the Bunsen burner at the gas tap puts out the fire because the gas is a switch that lets the amount of gas that you want to burn. And if you turn it off then it would let no gas through and there for would not let the Bunsen burner light up. Hope this helps


What is the wire called that connects the Bunsen burner to the gas tap?

it's hardly a wire, more of a tube I would say


Bunsen burner parts?

A Bunsen burner typically consists of a base, gas inlet tube, air control collar, barrel, and burner tip. The base is used to stabilize the burner, the gas inlet tube connects to the gas source, the air control collar adjusts the air flow, the barrel houses the flame, and the burner tip is where the gas mixes with air and ignites.


What is the functions of all the parts in a Bunsen burner?

Funtions of the Bunsen burner: air-hole: to control the amount of air let into the Bunsen burner for combustion. barrel: To allow the flame to beat a suitable height for burning. base: To support the Bunsen burner so that it will not fall over. collar: helps to adjust the gas being produced gas tap: to store gas. jet: To allow gas to enter the Bunsen Burner ( by helpingppl) Flame: the one part you don't want to forget

Related Questions

How do you use a Bunsen burner?

Put the rubber tubing onto the gas tap Then turn on the gas tap


What is a gas tap used for on a Bunsen burner?

The purpose is to control the combustible gas flow.


What will happen when the Bunsen burner strikes back?

You have to turn off the gas tap immediately.


How do you control the height of the flame on a bunsen burner?

The height of the flame on a Bunsen burner can be controlled by adjusting the gas supply using the gas tap. Turning the gas tap to increase the gas flow will raise the flame height, while decreasing the gas flow will lower the flame. Positioning the collar on the burner can also help control the air-to-gas ratio and influence the flame height.


Turning off the Bunsen burner at the gas tap puts out the fire because?

Turning off the Bunsen burner at the gas tap puts out the fire because the gas is a switch that lets the amount of gas that you want to burn. And if you turn it off then it would let no gas through and there for would not let the Bunsen burner light up. Hope this helps


What is the function of gas inlets in busen burner?

The primary function of a Bunsen burner is to provide fire for use in experiments. However, as fire requires oxygen to sustain the fire, the inlets provide this from the source of the fire further mixing it with the gas from the tap. This allows the fire to be contained and subsequently controlled. This is only me understanding of it


What is the wire called that connects the Bunsen burner to the gas tap?

it's hardly a wire, more of a tube I would say


What is the purpose of the desk outlet valve of a Bunsen burner?

The desk outlet valve of a Bunsen burner controls the airflow of the gas entering the burner. By adjusting this valve, you can regulate the amount of oxygen mixing with the gas, which in turn affects the type of flame produced and the temperature it can reach.


Bunsen burner parts?

A Bunsen burner typically consists of a base, gas inlet tube, air control collar, barrel, and burner tip. The base is used to stabilize the burner, the gas inlet tube connects to the gas source, the air control collar adjusts the air flow, the barrel houses the flame, and the burner tip is where the gas mixes with air and ignites.


Safety proceedures using the Bunsen burner?

Step one: Place the Bunsen burner on a heat proof mat Step two: Check that the rubber tubing is connected properly to the Bunsen burner and the gas tap. step 3: ensure that the air hole is closed Step 4: Light the math Step 5: Open the gas tap Step 6: Hold the burning math over the barrel. Make sure your hand is not in the passage of the flame.


What is gas tap used for?

A gas tap is used to control the flow of fuel gas (natural gas or, historically,coal gas, etc.) in the home (for gas fires or other appliances) or in laboratories (for Bunsen burners).


Why is it important to light the match before opening the gas tap when lighting a Bunsen burner?

It is important to light the match before opening the gas tap when lighting a Bunsen burner to prevent gas from escaping and potentially causing an explosion. Lighting the match first ensures that the flame is present to ignite the gas as it is released.